ThinkSystem RAID 730-8i PCIe 12Gb Adapter Update BIOS and Firmware (For Windows)

Change History

BIOS and Firmware Update for ThinkSystem RAID 730-8i XGB Cache PCIe 12Gb Adapter

Supported Adapters: 
				ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter  (7Y37A01083)
	            ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter  (4Y37A09722)

NOTE TO SERVICE - Reference RETAIN #N/A


Version 24.21.0-0126 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0126
BIOS: 6.36.00.3
UEFI Driver:0x06180203
HII: 03.25.05.12
MR NVDATA: 3.1705.00-0021
iMR NVDATA - 3.1705.01-0013
MR Firmware - 4.680.00-8519
iMR Firmware - 4.680.01-8518
MR 6.14

defects:
Incomplete onfi configuration leads to FW HALT.(DCSG00051973)
SAS9341-8i board encounters 'Previous configuration completely missing at boot' error.(DCSG00067176)
MR 6.14 - MR FW resets the controller on/off property "allowBootWithPinnedCache" on every boot.(DCSG00069702)
Unable to import foreign config.(DCSG00041146 (Port Of Defect DCSG00025975)
Repeated TASK ABORTS and access to the data store lost.(DCSG00066009 (Port Of Defect DCSG00063321))
Cache offload is not getting completed during dummy descriptor configuration.(DCSG00048845)


Version 24.21.0-0124 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0124
BIOS: 6.36.00.3
UEFI Driver:0x06180203
HII: 03.25.05.12
MR NVDATA: 3.1705.00-0020
iMR NVDATA - 3.1705.01-0012
MR Firmware - 4.680.00-8515
iMR Firmware - 4.680.01-8514
MR_6.14

Defects (21)
  - During config force clear, invader MR FW hits assertion.(SCGCQ02154000)
  - 614.1_FW: Controller is not detecting in OS on a latest FW pkg 24.21.0-0108 when expander is connected to controller and configured for zoning.(SCGCQ02157970)
  - Firmware crashes while running IO's with flushwriteverify=on.(SCGCQ02174924)
  - Triggering Back to Back OnDemand Snapdump leads to generation of Duplicate Snapdump entries/files.(SCGCQ02187566)
  - Firmware initialization failed. Fault code = 0x22 !!! observed during FW Downgrade/upgrade.(SCGCQ02191364)
  - Patrol Read never progresses when Patrol read rate is set to less than 10%.(SCGCQ02197015)
  - AVAGO_B doesn't reflect in boot VDs vendor ID if boot device is changed from JBOD to LD.(SCGCQ02162341)
  - Cache Data Loss with ONFI double dip with bad SuperCAP.(SCGCQ02167986)
  - Snapdump 6.14 - Check on the ONFI Data structures being dumped properly.(SCGCQ02182249)
  - Snapdump is not generating for Kill Adapter (when there is no IO TimeOut).(SCGCQ02189995)
  - Snapdump files are not getting erased after ~5 System Reboots, when Snapdump save count is set to 4.(SCGCQ02195001)
  - Assertion failure observed, when user has initiated KA and SD is disabled.(SCGCQ02198254)
  - MR FW marks Zoned Out PHYs as bad PHYs.(SCGCQ02152834)
  - During the push pull test, with different delay for each drive , leads to assert.(SCGCQ02157827)
  - As timeout happens for a command ,driver sends KA.(SCGCQ02169505)
  - Snapdump 6.14 - Clean up the snapdump table and its associated functions.(SCGCQ02181209)
  - MR_6.14: "SnapDumpDbg faultingModule 0 moduleBmp 1f6f faultFunc 0 FaultCode 1" Observed while trying to get Snapdump.(SCGCQ02198608)
  - DEV DEFECT: iMR 6.14 - Disable unused debug code compilations for Skinny.(SCGCQ02183672)
  - FW should clear the snapdump during personality change.(SCGCQ02194577)
  - MR 6.14 - Multi-bit ECC errors seen on Invader board in JBOD personality mode.(SCGCQ02207367)
  - Dev Defect: Snapdump 6.14: Addressing the review comments for ERs.(SCGCQ02174425)
  - Aero PA0.8: (Vision) Snapdump Fails to generate after Assertion failure in fw\cpu\arm\exceptions.c during Cable Push.(SCGCQ01940055 port of SCGCQ01918865)
  - Controller Hang after multiple iterations of S4 Sleeper Stress Test.(SCGCQ02099935 port of SCGCQ02059508)
  - MR7.10-9480-8i8e: DC during Single Dip COL Using Wingman Automation.(SCGCQ02140667 port of SCGCQ02077953)
  - [RHEL 8.1] system will hang with SME enable.(SCGCQ02192339 port of SCGCQ02184712)
  - Snapdump capture fails when COL restore occurs with ECC errors.(SCGCQ02197538 port of SCGCQ02041663)
  - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash.(SCGCQ02113872 port of SCGCQ01973389)
  - EKMS 10.3: Reboot loop results in OS getting corrupted i,e 0xC000000E (Required Device is Inaccessible).(SCGCQ02140049 port of SCGCQ02080146)
  - Recon operation can lead to silent data corruption in certain scenarios.(SCGCQ02195549 port of SCGCQ02191510)
  - sense data returned from out-of-band storlibtest is wrong.(SCGCQ02112236 port of SCGCQ02050648)
  - Aero A0 UTP - Atlas Config NVMe3 TM + Cable pull/push results in CORE0 fault and OCR(SCGCQ02140684 port of SCGCQ02041132)
  - Security Subsystem Errors.(SCGCQ02157832 port of SCGCQ02139169)
  - DEV DEFECT: iMR 6.14 - Disable unused debug code compilations for Skinny.(SCGCQ02187494 port of SCGCQ02183672)
  - Aero UTP: On-demand snapdump lost when created before learn cycle on new SCAP.(SCGCQ02197294 port of SCGCQ02059851)
  - Aero PA4: getting on-demand snapdump right after FW flashing causes a FW exception.(SCGCQ02140030 port of SCGCQ02125329)
  - Fix to clear stale RLM failure state that fails subsequent RLMs.(SCGCQ02188879 port of SCGCQ02174426)
  - Snapdumps may include empty files if one of the file streams exceeds the allocated buffer.(SCGCQ02197295 port of SCGCQ02138164)
  - foreign import failed when sequence number mismatch.(SCGCQ01940056 port of SCGCQ01912560)
  - DEV DEFECT: iMR 6.14 - Disable unused debug code compilations for Skinny.(SCGCQ02190332 port of SCGCQ02183672)
 
EnhancementRequests (20)
  - Removed VDM driver workaround.(SCGCQ02144055)
  - Support LED functionality on disjoint SGPIO back-planes that report non-contiguous slot numbers.(SCGCQ02144062)
  - Snapdump base framework for Invader 6.14.(SCGCQ02150008)
  - Snapdump-6.14: Zmodem infrastructure support.(SCGCQ02151362)
  - Snapdump offload and restore across the abrupt reboots.(SCGCQ02165912)
  - Snapdump 6.14 Raid module: Generate snapdump when pinned cache is generated.(SCGCQ02172218)
  - Support Zone In and Zone Out functionality for MR 6.x Channel.(SCGCQ02129396)
  - Snapdump 6.14: Snapdump need to be retained after the OCR.(SCGCQ02164133)
  - Snapdump 6.14: Raid support-DDF module integration.(SCGCQ02174431)
  - TTY module integration to Snapdump.(SCGCQ02175357)
  - Generate Snapdump upon observing Data abort exceptions.(SCGCQ02180497)
  - 6.14 SnapDump: Controller property support for enabling snapDump.(SCGCQ02154867)
  - 6.14 SnapDump:Print re-routing frame work.(SCGCQ02154870)
  - Generate Snapdump on observing assertions and PL faults.(SCGCQ02165909)
  - DM module integration to Snapdump.(SCGCQ02172283)
  - Snapdump 6.14: Raid support-ONFI module integration.(SCGCQ02175257)
  - PL module integration to Snapdump.(SCGCQ02179473)
  - Snapdump 6.14: Early notification handling from driver for generation of snapdump.(SCGCQ02181283)
  - Snapdump 6.14 - Support of IOP related dump.(SCGCQ02182263)
  - SnapDump 6.14 :Integration of DDR framework to support snapdump.(SCGCQ02150010)


Version 24.21.0-0112-1 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0112-1
BIOS: 6.36.00.3
UEFI Driver: 0x06180203
HII:  03.25.05.12
MR NVDATA: 3.1705.00-0020
iMR NVDATA - 3.1705.01-0012
MR Firmware - 4.680.00-8489
iMR Firmware - 4.680.01-8488
MR 6.14

Defects (15)
 - LD Inquiry still show as AVAGO_B for VD even when JBOD drive is set as boot PD.(SCGCQ02052706)
 - Fatal FW error observed on connecting enclosure in a multipath or cascading another enclosure when slot based device ID feature is enabled.(SCGCQ02141291)
 - Fix API changes done for NVMe readiness(SCGCQ02142981)
 - Add NVMe width comments to mr.h(SCGCQ02146846)
 - During SpinUpRecoveySM 2/4/1C sense data is not handled(SCGCQ02149370)
 - Non boot VD gets vendor identification as "AVAGO_B" for a specific OEM(SCGCQ02160670)
 - Boot VD Inquiry String is not retained, after foreign importing the Boot VD configuration(SCGCQ02057908)
 - montask observed inline 1704 in ../../raid/bootMsg.c during enclosure cable pull/push.(SCGCQ02136344)
 - Flaky link drive connection causing a fatal error.(SCGCQ02141740)
 - SED drive moved to fail state during device missing delay (DMD)(SCGCQ02144016)
 - IOUNITPAGE 11 parameters are not updated in the next boot.(SCGCQ02154597)
 - TUR timeout increased from 64 sec to 120sec.(SCGCQ02118063)
 - When slot based device ID feature is enabled, Drive Slot id and device ids are not matching after hot plug of direct attached drives(SCGCQ02144003)
 - 6.14_FW : Fatal FW error observed on iMR controller after flashing latest FW pkg 24.21.0-0111 and rebooting the system.(SCGCQ02171024)
 -(SCGCQ02102580)
 - Initialize cache after diagnostics testing(SCGCQ02157830 port of SCGCQ02134286)
 - CSCuv03959 DPMR6 - System hung after abort running CC continuously overnight.(SCGCQ02169538 port of SCGCQ00883695)
 - IO Error observed on few VD's, after setting the boot drive in NVMe Mix Mode Configuration(SCGCQ02099404 port of SCGCQ02058292)
 - Kill Adapter if PD FW download is run in continous loop(SCGCQ02139082 port of SCGCQ02059825)
	
EnhancementRequests (32)
 - Add New Generic OOB API To Read ROC Temp, Drive Temp, Drive Type, Drive Protocol and status through OOB BMC(SCGCQ01940661)
 - Add a new log event used whenever the snap dump properties are modified.(SCGCQ01963328)
 - Add a bit for atomic descriptor capable(SCGCQ01965047)
 - Add CTRL_SB_SOFT_SECURE_MODE event to indicate soft secure mode(SCGCQ01965721)
 - Introduced new controller bit(SCGCQ01985474)
 - Customer needs to generate and extract the On-demand based debug data both for MR and iMR.(SCGCQ02000566)
 - Driver parameter bit for support of tool box cmd(SCGCQ02002119)
 - Add new MFI Fault sub code for Secure Boot Preboot Auth failure(SCGCQ02006657)
 - Reword event log messages as it creates unnecessary panic.(SCGCQ02013675)
 - Modification in MR_SNAPDUMP_TRIGGER_TYPE enum value(SCGCQ02030653)
 - Additional details about spare(SCGCQ02033538)
 - API change to support NVMe Passthrough over OOB(SCGCQ02035295)
 - API change to support new DCMD for consolidated device list(SCGCQ02037158)
 - API changes for NVMe speed and width changes(SCGCQ02053667)
 - API changes for linkconfig interface(SCGCQ02053671)
 - Increase in MR_PD_INFO.name length to 32 characters(SCGCQ02079068)
 - MR Windows IOCTL Error codes to Application added to MR API(SCGCQ02103183)
 - Add MFI STAT and MR Event for Secure Boot indicating fw dl was not allowed due to an existing pending key change(SCGCQ02103973)
 - Better error message for certain unmap operations(SCGCQ02111563)
 - OEM request to implement slot based device ID for direct attached or enclosure connected drives(SCGCQ02111943)
 - As per OEM request bypassing the cache for particular workload on 512E drives.(SCGCQ02123808)
 - Add disableOffloadNum field in MR_SNAPDUMP_PROPERTIES struct(SCGCQ02125252)
 - API changes for a better presentation of Atlas to tools(SCGCQ02149380)
 - API changes for Lane Margining(SCGCQ01921241)
 - Standard SCSI Inquiry vendor identification should be “AVAGO_B” for VD that is set as boot device(SCGCQ02030668)
 - Unlocking FDE disk after a power-on-reset (POR(SCGCQ02050712)
 - MR API: Add support bits for currentSpeed and clkMode(SCGCQ02132334)
 - Adding NVACHE messages indicate when SLC format has started and completed(SCGCQ02137048)
 - FW prints SASIOUnitPage 11 during boot up.(SCGCQ02144058)
 - Change the order of DDF header updates when there are errors existing in DDF headers currently on the drive(SCGCQ02124249)
 - Enhance data collection when a MU error is seen(SCGCQ02134251)
 - Unblock and allow the SCSI pass-through commands to bad/failed/offline PDs(SCGCQ02136394)

Version 24.21.0-0097 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0097
BIOS: 6.36.00.3
UEFI Driver: 0x06180203
HII: 03.25.05.12
MR NVDATA: 3.1705.00-0018
iMR NVDATA - 3.1705.01-0012
MR Firmware - 4.680.00-8458
iMR Firmware - 4.680.01-845
MR 6.14

defects:
 SATA PD does not change to failed state after read medium error detected(SCGCQ01624704) 
 - Repetitive OOB and LED prints observed in FW logs(SCGCQ01727104) 
 - FW Crashes when user tries to fetch SMP PassThru Info using Host SLT(SCGCQ01937319) 
 - Do not allow RAID config in JBOD-WB mode and prevent change of personality if WB mode is set(SCGCQ01685447) 
 - dev defect - Setting defaults for JBOD-WB mode and code cleanup(SCGCQ01681100) 
 - Cannot create or mount xfs filesystem using xfsprogs 4.19.x kernel 4.20(SCGCQ02027889) 
 - xfs_info command run on an XFS file system created on a VD of strip size 1M shows sunit and swidth as 0(SCGCQ02056038) 
 - CV going into WT mode during learn after upgrading to versions later than 24.18.0-0021 - FW fault after factory defaults(SCGCQ02060813) 
 - After using hdparm to lock a SATA SSD JBOD drive the drive fails to be unlocked by the MR FW on reboot(SCGCQ02083536) 
 - Kill adapter observed while running target reset on JBOD WB(SCGCQ01789188) 
 - SMp command failure in OOB Path(SCGCQ01927021) 
 - HDET_MR 6.14: OOB - SCSI PassThru Command fails with error code 0x2E	(SCGCQ01936541) 
 - Once pinnedcache is set to off not able to toggle field value in JBOD WB mode(SCGCQ01671213) 
 - PL Fault observed while running target reset on JBOD WB(SCGCQ01676164) 
 - MR 6.14: FW reported incorrect value for max data transfer request size as 4 MB in Storcli app.(SCGCQ02023160) 
 - Kill Adapter observed while running task management on JBOD-WB with IO's	(SCGCQ02009801) 
 - Max number of PDs for PatrolRead to run concurrently should be in range from 1 to MR controller's max configurable PDs(SCGCQ02008420) 
 - Some Configured drives may change to JBOD and Unconfigure Good after Set JBOD=on and reboot(SCGCQ02080101) 
 - MR controller was missing in UEFI after reboot when the bootable JBOD drive was removed(SCGCQ02112533) 
 - MR API - Incorrect value used for MR_DCMD_CTRL_SNAPDUMP_ONDEMAND	(SCGCQ01882581) 
 - MR 6.14 - PD show all StorCLI command fails for UBAD SAS & SATA drives	(SCGCQ01915285) 
 - With ESXi 6.7 OS or latter, a SATA SSD drive that is configured as EPD will be dropped by OS when driver reload is done(SCGCQ01969605) 
 - Dev defect: Incorporate the new changes done in MR API(SCGCQ01760667) 
 - Amber LED not seen for UBAD PD's	(SCGCQ01770256) 
 - Continuous SRAM correctable error prints followed by controller reset(SCGCQ02023839) 
 - Able to create RAID configuration even after it has been disabled(SCGCQ01670086) 
 - With a pending personality change, Global hot spares are allowed to be created and should be blocked.(SCGCQ01750315 port of SCGCQ01742187)
 - SMP pass through not working when the “PD 0” is BAD drive(SCGCQ01945674 port of SCGCQ01945602)
 - (CSETActivity) - MCTP over PCIe discovery(SCGCQ01904092 port of SCGCQ01184923)
 - CIT: Same EID assigned to 2 930-8i controllers(SCGCQ01886616 port ofSCGCQ01830180 )
 - Controller OCR seen when DM multipathing issues read CDB with zero blocks(SCGCQ01822167 port of SCGCQ01808882)
 - Unable to recover config when changing security password before re-inserting drives(SCGCQ01874302 port of SCGCQ01715058)
 - 23=Flash programming error while upgrading the Controller FW causes the APP image corruption(SCGCQ02085501 port of SCGCQ02074630)
	
EnhancementRequest:	
 - RTTrace Enable/Disable API changes(SCGCQ01830211) 
 - MR API changes to support EKMS over OOB(SCGCQ01874035) 
 - API Changes for Driver/FW DCMD HandShake(SCGCQ01841266) 
 - Added new events for unmap policy change(SCGCQ01871912) 
 - Add secure boot key update complete event(SCGCQ01928254) 
 - Including The Time Stamp for every Snap Dump created in the firmware.(SCGCQ01797424) 
 - Unmap: Define new events for enhanced UNMAP support [MR7.8](SCGCQ01803319) 
 - Deprecate the snap dump fields that are no longer needed for MR_SNAP_DUMP_PROPERTIES structure(SCGCQ01816724) 
 - [MR 7.8] API change to return apt failure status for a personality change request(SCGCQ01853480) 
 - Interrupt coalsecing setting per group of 8 replies queues (h/w VF registers	(SCGCQ01886424) 
 - HDET: Support smp passthrough storeliboob (API changes requirement(SCGCQ01916035) 
 - Add secure boot support(SCGCQ01792416) 
 - API change to provide learn complete timestamp(SCGCQ01845269) 
 - POC in 6.14: WB support and Pinned Cache changes(SCGCQ01581022) 
 - Aero FW - Reporting SSD wear gauge values for OEM specific customers(SCGCQ01798686) 
 - Support SC_INQUIRY and SC_LOG_SENSE SCSI Passthrough commands on drives in bad state for a particular OEM(SCGCQ01888257) 
 - FW changes for the configurable parameters(SCGCQ01609320) 
 - Add the API to clear all the snap-dumps from firmware.(SCGCQ01824135) 
 - API Changes - After Vision PSOC FW update, applications should ask the user for power cycle instead of reboot(SCGCQ01765150) 
 - Add new MFI Status - MFI_STAT_PD_NOT_ELIGIBLE_FOR_LD	(SCGCQ01818580) 
 - HDET: Support smp passthrough in storlib and storeliboob	(SCGCQ01799154) 
 - Fail the drive and do not pin the cache(SCGCQ01584411) 
 - Integrated Invader PL RO - SCGCQ02000507– phase 14, Version 14.00.11.00 to MR 6.14(SCGCQ02000920) 
 - [MR 7.8] API change to export "disable least latency mode"(SCGCQ01887495) 
 - Fix MR_CTRL_INFO to support backward compatibility(SCGCQ01946548) 
 - Added customer serial number field to MFC Manufacturing 2 structure(SCGCQ01873417) 
 - Added Support for Triggering SnapDump(SCGCQ01848759) 
 - Add Board Support Package Image Type to MR_IMAGE_TYPE(SCGCQ01931637) 


Version 24.21.0-0084-1 - Moderate Impact/Low Probability of Occurrence
--------------------

PACKAGE: 24.21.0-0084
BIOS: 6.36.00.3
UEFI Driver: 0x06180203
HII: 03.25.05.11
NVDATA: 3.1705.00-0018
iMR NVDATA - 3.1705.01-0012
Firmware - 4.680.00-8434
iMR Firmware - 4.680.01-8435
MR 6.14 
Defects:
- SATA SSD not discovered by OS during hibernate test.(SCGCQ01949781)
- Intruder and Invader controllers returnning vpd86 error.(SCGCQ01929277)
- FW reports that the board passed BBU Retention test on boards that have a non operational ONFI NAND memory.(SCGCQ01891177 Port Of Defect SCGCQ01934351)
- Invader IMR : PD fails to get marked as foreign on insertion.(SCGCQ01950845 Port Of Defect SCGCQ01955263)
- Preserved Cache doesn't flush back during Foreign Import.(SCGCQ01466831 Port Of Defect SCGCQ01904085)


Version 24.21.0-0076-1 - Moderate Impact/Low Probability of Occurrence
--------------------

PACKAGE: 24.21.0-0076 
BIOS:  6.36.00.3
UEFI Driver: 0x06180203
HII:  03.25.05.10
NVDATA: 3.1705.00-0018
iMR NVDATA - 3.1705.01-0012
Firmware - 4.680.00-8417
iMR Firmware - 4.680.01-8406

Defects (8)
- 'CacheVault Flash Size' is showing as 3.0 GB after upgrading FW when it should show 4.0 GB.(SCGCQ01615779)
- criteo: Storcli shows R0 VD as WB in JBOD personality where as FW shows in WT mode.(SCGCQ01714445)
- Revert code changes from CSET SCGCQ01569257.(SCGCQ01717743)
- Customer specific 3108 PCIe add-on card fails to come back while resuming from sleep state S.(SCGCQ01718911)
- FW returns success for enabling encryption when it is failed on the drives.(SCGCQ01830718)
- Line 535 in ../../raid/cachePreserve.c for trying to create Pinned Cache by Cable Pull..(SCGCQ01839662)
- memset the deviceStateLedBitmap properly.(SCGCQ01844264)
- OOB SCSI passthru command (READ DEFECT 12) return without response data.(SCGCQ01793262)
- FW is observing Kill Adapter while CCVD disassociate in progress.(SCGCQ01186806 port of SCGCQ01172369)
- Update the MAXTransferLength properly for Driver enabled 1MB support feature.(SCGCQ01238543 port of SCGCQ01232275)
- FW crashes when FW update(OFU) is done with faluty onfi.(SCGCQ01249569 port of SCGCQ01227115)
- irq handler flooding taskqueue and persistent ID removal corrupting memory.(SCGCQ01399132 port of SCGCQ01299784)
- Firmware allows to add bad blcoks beyond actual number of blocks..(SCGCQ01430024 port of SCGCQ01403292)
- MCTP: Addressing PCIe credirt free issue..(SCGCQ01447186 port of SCGCQ01446811)
- Firmware discovery is not listing all the drives after removal/insert Enclosure Cable with IO.(SCGCQ01579250 port of SCGCQ01555943)
- MR FW memory Leak across driver load/unload.( SCGCQ01579251port of SCGCQ01573393)
- With controller operating in least latency mode, FW hits montask upon running IOs.(SCGCQ01587048 port of SCGCQ01116419)
- Increase the recon BB list entries to align with BBM MAX BAD entries.(SCGCQ01635416 port of SCGCQ01623254)
- Issue: JBOD devices were dropped after unloading driver and reloading driver in linux.(SCGCQ01639846 port of SCGCQ01566087)
- : FW asserts when invalid parameters to set excluded ld for CC is sent to firmware..(SCGCQ01670394 port of SCGCQ01635729)
- Colusa SAS expander reset results in unpredictable performance.(SCGCQ01697517 port of SCGCQ01455811)
- MR 7.6 - "NVCache has gone bad" during POST after flashing the latest package 1226 and rebooted.(SCGCQ01714326 port of SCGCQ01635062)
- When NVRAM value is read from cached address ,primary core reads stale value and skips writing to NVRAM..(SCGCQ01715349 port of SCGCQ01676080)
- F/W Hangs during reboot.(SCGCQ01716602 port of SCGCQ01616551)
- MR7.6: Firmware hit montask running task management reset in loops.(SCGCQ01727364 port of SCGCQ01675742)
- When NVRAM value is read from cached address ,primary core reads stale value and skips writing to NVRAM.(SCGCQ01729680 port of SCGCQ01676080)
- LAS does not show proper state of secured locked drives..(SCGCQ01732045 port of SCGCQ01615781)
- F/W Hangs during reboot.(SCGCQ01758976 port of SCGCQ01616551)
- Pd firmware download timer is calculated accordingly.(SCGCQ01758988 port of SCGCQ01669508)
-.(SCGCQ01763953 port of SCGCQ01749090)
- Smart Return Status passthru command failed on SATA drives.(SCGCQ01806402 port of SCGCQ01555033)
- LAS does not show proper state of secured locked drives..(SCGCQ01807819 port of SCGCQ01615781)
-.(SCGCQ01838484 port of SCGCQ01807938)
- 9460-8i is reporting Chip Temperature of 255 when the ambient temp is about 0 C.(SCGCQ01850339 port of SCGCQ01565568)
- Found invalid event.(SCGCQ01375915 port of SCGCQ01347858)
- 9460-16i disappears from F1 setup after encrypting SED.(SCGCQ01565312 port of SCGCQ01326871)
- Sanitize Support.(SCGCQ01577753 port of SCGCQ01526323)
- Increase the recon BB list entries to align with BBM MAX BAD entries.(SCGCQ01633668 port of SCGCQ01623254)
- Sanitize progress in TTY log showing incorrect elapsed time.(SCGCQ01681594 port of SCGCQ01630577)
- Pd firmware download timer is calculated accordingly.(SCGCQ01682987 port of SCGCQ01669508)

EnhancementRequests (11)
- Integrate phase 12 PL (12.00.13.00) with MR 6.12.(SCGCQ01580766)
- FW change: Request to add NVDATA and PNP IDs for new card introduction.(SCGCQ01826466)
- Integrate Intruder Phase 14 PL - 14.00.10.00 Firmware MR PL Release.(SCGCQ01764776)
- Criteo: API changes reversal.(SCGCQ01760512)
- PL Integration: Integrate Intruder PL phase 13.00.10.00 with MR 6.13 Intruder.(SCGCQ01698033)
- PL Integration : Integrate Invader phase 12.00.14.00 PL with MR 6.12.(SCGCQ01716598)
- RTTrace API Changes.(SCGCQ01745568)
- Mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled..(SCGCQ01757538)
- Unmap: Define new API for enhanced UNMAP support.(SCGCQ01758062)
- Adding API bit to indicate whether forced personality change is supported or not..(SCGCQ01762153)
- PL Integration: Integrate Invader Phase 13.00.10.00 PL with MR 6.13 Invader.(SCGCQ01698045)


Version 24.21.0-0052-1 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE:  24.21.0-0052
BIOS:  6.36.00.2
UEFI Driver:  0x06180202
HII:  03.25.05.04
NVDATA: 3.1705.00-0014
iMR NVDATA - 3.1705.01-0011
Firmware - 4.680.00-8353
iMR Firmware - 4.680.01-8354

Defects (42)
- Intruder Controller Disappear during clean shutdown on OEM server.(SCGCQ01375977)
-.(SCGCQ01753405)
-.(SCGCQ01749090)
- When NVRAM value is read from cached address ,primary core reads stale value and skips writing to NVRAM..(SCGCQ01676080)
- Pd firmware download timer is calculated accordingly.(SCGCQ01669508)
- IO path function accessed by both core is not synchonized..(SCGCQ01640234)
- False alarm of "cache Discarded" when the System, with Invader controller + WT R5 volume, is shutdown normally..(SCGCQ01627751)
-.(SCGCQ01623408)
- Increase the recon BB list entries to align with BBM MAX BAD entries.(SCGCQ01623254)
- MR FW memory Leak across driver load/unload.(SCGCQ01573393)
- Incorrect Micron NAND Model Number read from flash.(SCGCQ01531136)
- MR_6.14 PACK 23 - On performing a cable pull/push operation during drive is in failed state, result to MonTask.(SCGCQ01529830)
- [Factory issue] MR 3108 controller BIOS stop at 3 different initialization screen.(SCGCQ01497858)
- IO access to iMR FW will fail after sveral powercycle.(SCGCQ01494761)
- iMR Compilation fails even with RELEASE option in 6.12 after taking errata MR workaround SCGCQ01323607 and its child defects.(SCGCQ01494566)
- SED Drive become UBad during secure erase on MegaRAID 9361-8i controller.(SCGCQ01473188)
- 6.14 : Reverting the sysDma changes.(SCGCQ01465727)
- On iMR Invader & for 2 enclosures connected in cascaded multi path , power off and then power on the 1st enclosure, PDs not getting detected.(SCGCQ01455949)
- Firmware upgrade/downgrade operation failing on SKINNY controller.(SCGCQ01455133)
- MCTP: Addressing PCIe credirt free issue..(SCGCQ01446811)
- Parameter Page Invalid, Setting channel count based on DDR Size..(SCGCQ01440768)
- FW breaks into montaks with pinned cache and foreign configuration.(SCGCQ01378970)
- FW reported tmm Date of Manufacture 15/25/6.(SCGCQ01395084)
- Interrupting Offload will Lead to Next offload cycle to fail.(SCGCQ01399701)
- Enable WB support via API.(SCGCQ01405242)
- F/W Hangs during reboot.(SCGCQ01616551)
- iMR compilation breaks, exceeding 1MB flash region allocated.(SCGCQ01520940)
- Extend iMR change of trap related data should be in same module as trap ISR..(SCGCQ01514867)
- Workaround for IO access to iMR FW will fail after sveral powercycle on 3004 controller..(SCGCQ01507504)
- linker error resolved.(SCGCQ01472217)
- Problem with I2C Slave communication with external Masters that don’t support slave clock stretching..(SCGCQ01443277)
- MR : Cache data Lost when Term Log is set to "on" and grown bad blocks are there in the controller.(SCGCQ01394288)
-.(SCGCQ01400707)
- Learn cycle shown as active when Learn cycle fails.(SCGCQ01400807)
- Firmware allows to add bad blcoks beyond actual number of blocks..(SCGCQ01403292)
- OCR getting disabled after NVRAM delete.(SCGCQ01719006)
- MCTP : Porting of firmware download fixes from Ventura.(SCGCQ01439651)
- NVCache state not transitioning from 'Faulty' to 'Ok' until after reboot.(SCGCQ01395724)
- Intermittent: On iMR_Invader & cascaded Enclosures, after power off the enclosure, FW holds the PD info and apps display PDs.(SCGCQ01483727)
- controller VPD info is hidden as per OEM request.(SCGCQ01454973)
- SSD SATA JBOD discovered as 0.0MB after re-loading the same driver..(SCGCQ01446965)
- Firmware discovery is not listing all the drives after removal/insert Enclosure Cable with IO.(SCGCQ01555943)
- Infinite loop in onfiSyncModeEnter.(SCGCQ01259314 port of SCGCQ00329024)
- HW workaround implementation for SCGCQ00830272 and SCGCQ01048567.(SCGCQ01326393 port of SCGCQ01323607)
- MR_6.14: Intruder PCI Trapping ISR incorrect logic for config trap address.(SCGCQ01334364 port of SCGCQ01332947)
- Firmware crashes during medium error recovery and Rebuild.(SCGCQ01348660 port of SCGCQ01304521)
- Resulting R0 VD is showing as not consistent after reconstruction..(SCGCQ01348998 port of SCGCQ01288897)
- Imr Invader FW crashes while upgrading from Pkg 24.18.0-0021 to Pkg 24.21.0-0007..(SCGCQ01351814 port of SCGCQ01342601)
- Intruder 4G DDR tuning value has to be changed in MR FW..(SCGCQ01369344 port of SCGCQ01368845)
- Found invalid event.(SCGCQ01375914 port of SCGCQ01347858)
- Placement of an image checkword at data area of NOR flash leads to controller crash.(SCGCQ01375943 port of SCGCQ01375071)
- Block OCR after Clearing NVRAM.(SCGCQ01392471 port of SCGCQ01386919)
- Block OCR after Clearing NVRAM.(SCGCQ01394920 port of SCGCQ01386919)
- SCS/PL debug logs for "rb", "tb", or "dmdiag pl dbg" are sometimes mangled due to multiple mprintf's overlapping.(SCGCQ01399457 port of SCGCQ01283702)
- RedBrick controller hang at DCR Err Logg Address 29e02..(SCGCQ01412795 port of SCGCQ01375159)
- RedBrick controller hang at DCR Err Logg Address 29e02..(SCGCQ01412827 port of SCGCQ01375159)
- LSA hangs when user try to change drive security key..(SCGCQ01412848 port of SCGCQ01342655)
- B200M4 (Carmel/ 3108 iMR): driver crashed after FW update via UCSM (UCSM bundle 2.2(8fS2)A/B to 3.1(2.163)A/B).(SCGCQ01412896 port of SCGCQ01271186)
- Parameter Page Reads fail during ONFI bringup..(SCGCQ01415428 port of SCGCQ01413557)
- heck Consistency doesn't identify double media errors once aborting and starting CC again.(SCGCQ01421932 port of SCGCQ01411591)
- heck Consistency doesn't identify double media errors once aborting and starting CC again.(SCGCQ01421933 port of SCGCQ01411591)
- heck Consistency doesn't identify double media errors once aborting and starting CC again.(SCGCQ01421934 port of SCGCQ01411591)
- Revert the DDR tuning values back to default value.(SCGCQ01446963 port of SCGCQ01444640)
- PL considers Timer Handle=0 and invalid, MR FW did not..(SCGCQ01446983 port of SCGCQ01399026)
- MCTP: Addressing PCIe credirt free issue..(SCGCQ01447187 port of SCGCQ01446811)
- Parameter Page Invalid, Setting channel count based on DDR Size..(SCGCQ01447901 port of SCGCQ01440768)
- Drives in Enclosure spin up values for OEM board is not initialized correctly.(SCGCQ01466081 port of SCGCQ01450221)
- IOMMU fault at address 0x80360000.(SCGCQ01473355 port of SCGCQ01279547)
- Enable DO_REAL_TIME_ISP and DO_DISABLE_ISP_CLAMP flags while flashing CPLD for Intruder cards.(SCGCQ01503730 port of SCGCQ01452026)
- SED Drive become UBad during secure erase on MegaRAID 9361-8i controller.(SCGCQ01503736 port of SCGCQ01473188)
- [Factory issue] MR 3108 controller BIOS stop at 3 different initialization screen.(SCGCQ01519905 port of SCGCQ01497858)
- MR_6.14 PACK 23 - On performing a cable pull/push operation during drive is in failed state, result to MonTask.(SCGCQ01532358 port of SCGCQ01529830)
- OCR is disabled by default is RC build, even NVDATA if it is enabled..(SCGCQ01540279 port of SCGCQ01503204)
- MR7.1/7.3 Termlog/UARTlog - messages sometimes missed in Termlog.(SCGCQ01540361 port of SCGCQ01498188)
-.(SCGCQ01569257 port of SCGCQ01097035)
- If an INVALID applicationMsgTag id received, then failed the command with MFI_OOB_STATUS_INVALID_CMD using command id MAX_OOB_COMMANDS..(SCGCQ01575976 port of SCGCQ01337332)
- Sanitize Support.(SCGCQ01577752 port of SCGCQ01526323)
- SATA PassTrough commands with check condition taking long time to complete..(SCGCQ01582512 port of SCGCQ01561887)
- VMware Passthrough Adapter does not sync time on VM power on.(SCGCQ01595865 port of SCGCQ01592800)
- Jbod become Ugood sometimes after reboot.(SCGCQ01616609 port of SCGCQ01508978)
- Colusa SAS expander reset results in unpredictable performance.(SCGCQ01618030 port of SCGCQ01455811)
- 'CacheVault Flash Size' is showing as 3.0 GB after upgrading FW when it should show 4.0 GB.(SCGCQ01640816 port of SCGCQ01615779)
- Drives are reverted back to JBOD after perfoming instant secure erase.(SCGCQ01683366 port of SCGCQ01615777)
- MR7.1/7.3 Termlog/UARTlog - messages sometimes missed in Termlog.(SCGCQ01714377 port of SCGCQ01498188)
- In HII whether entering the correct pass phrase or the wrong pass phrase a secured SED becomes unsecured.(SCGCQ01715297 port of SCGCQ01301947)
- B200 M5 / Carmel (3108 iMR) - VSAN failure during controller reset test.(SCGCQ01760837 port of SCGCQ01397566)
- MR 6.14 Beta: MonTask: line 245 in file ../../raid/1078int.c while running reboot test with background operations.(SCGCQ01339329 port of SCGCQ01332706)
- MR : Cache data Lost when Term Log is set to "on" and grown bad blocks are there in the controller.(SCGCQ01403930 port of SCGCQ01394288)
- Interrupting Offload will Lead to Next offload cycle to fail.(SCGCQ01403958 port of SCGCQ01399701)
- SSD SATA JBOD discovered as 0.0MB after re-loading the same driver..(SCGCQ01447007 port of SCGCQ01446965)
- MCTP : Porting of firmware download fixes from Ventura.(SCGCQ01447173 port of SCGCQ01439651)
- Controller crash observed while running OLTP workload (4K and 16K 16QD).(SCGCQ01447780 port of SCGCQ01438216)
- PL considers Timer Handle=0 and invalid, MR FW did not..(SCGCQ01467708 port of SCGCQ01399026)
- [Factory issue] MR 3108 controller BIOS stop at 3 different initialization screen.(SCGCQ01519906 port of SCGCQ01497858)
- Extend iMR change of trap related data should be in same module as trap ISR..(SCGCQ01521684 port of SCGCQ01514867)
- Event Log Corruption..(SCGCQ01532399 port of SCGCQ01451417)
- Rebuild Rate %100 takes much longer time than %30 while running IO. It should take much shorter time..(SCGCQ01540424 port of SCGCQ01336908)
- Controller crash observed while running OLTP workload.(SCGCQ01565253 port of SCGCQ01447773)
- OEM iMR 8i controller fails to complete an OCR.(SCGCQ01565318 port of SCGCQ01330611)
- Snap3 : Drives drops while running transformation operation on R1 to R5 with 900 Medium errors.(SCGCQ01598538 port of SCGCQ01581661)
- LSA shows Stop Erase option for VDs on which Erase operation is not in progress.(SCGCQ01605097 port of SCGCQ01600267)
- Memset the PinnedDataStructure when DRAM dirty signature is zero.(SCGCQ01724925 port of SCGCQ01713149)
- Firmware crashes during medium error recovery and Rebuild.(SCGCQ01348657 port of SCGCQ01304521)
- Firmware crashes during medium error recovery and Rebuild.(SCGCQ01348658 port of SCGCQ01304521)
- FW is not correctly reporting Hide VD operation as not supported.(SCGCQ01348841 port of SCGCQ01274084)
- MR7.3: 4k PD Configuration can't be imported from iMR to MR Controller. However, it can be imported from MR to iMR.(SCGCQ01402828 port of SCGCQ01395842)
- PL considers Timer Handle=0 and invalid, MR FW did not..(SCGCQ01467725 port of SCGCQ01399026)
- Extend iMR change of trap related data should be in same module as trap ISR..(SCGCQ01520788 port of SCGCQ01514867)
- MR 7.6 - "NVCache has gone bad" during POST after flashing the latest package 1226 and rebooted.(SCGCQ01683358 port of SCGCQ01635062)
- Controller hang with FDE Drive (Micron 510DC).(SCGCQ01328038 port of SCGCQ01304133)
- Assertion failure in ../../mros/mem.c : mb->tag==tag.(SCGCQ01539460 port of SCGCQ01515324)
- Parameter Page Reads fail during ONFI bringup..(SCGCQ01415424 port of SCGCQ01413557)
- If an INVALID applicationMsgTag id received, then failed the command with MFI_OOB_STATUS_INVALID_CMD using command id MAX_OOB_COMMANDS..(SCGCQ01512549 port of SCGCQ01337332)


EnhancementRequests (47)
- New events for PR/CC conflicts and sector size mismatch.(SCGCQ01227051)
- Provide customized default smartpollinterval to 30 for iMR3004 product.(SCGCQ01748252)
- RTTrace API Changes.(SCGCQ01745568)
- API changes needed to support eHBA product series.(SCGCQ01727346)
- Create sanitize events.(SCGCQ01713708)
- Memset the PinnedDataStructure when DRAM dirty signature is zero.(SCGCQ01713149)
- Integrate latest phase 14.0 - 14.00.08.00 PL with MR 6.14.(SCGCQ01682170)
- as per customer request enabled FBU02 and 4G TFM support.(SCGCQ01681106)
- Modify event string APIs for MISSING and OFFLINE LDs.(SCGCQ01628177)
- New configuration params added for EPD-PT devices.(SCGCQ01599607)
- MR API change request to Enable/disable the parallel PD FW update feature based on PNP ID’s.(SCGCQ01595347)
- Integrate latest phase 14 PL with MR 6.14.(SCGCQ01593998)
- Integrate Invader Phase 14 PL - 14.00.06.00 Firmware MR PL Release.(SCGCQ01589431)
- Add support to defeature Cached I/O policy.(SCGCQ01581032)
- Implement Snapdump debugging capability.(SCGCQ01567770)
- Integrate Intruder phase 14 PL - 14.00.08.00 with MR 6.14 Intruder.(SCGCQ01459161)
- customer request for GPIO support..(SCGCQ01452102)
- Enable DO_REAL_TIME_ISP and DO_DISABLE_ISP_CLAMP flags while flashing CPLD for Intruder cards.(SCGCQ01452026)
- Fail to Set SSDSmartErEnabled to TRUE when copyback is disabled.(SCGCQ01403999)
- PL 14.00.07.00 intgration to MR 6.14 intruder..(SCGCQ01401110)
- Integrate phase 14 Intruder PL - 14.00.06.00 with MR 6.14.(SCGCQ01386225)
- Add "Incompatible with Profile" event.(SCGCQ01289924)
- Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01216848)
-.(SCGCQ01389581)
- Add Test Link Diagnostic API.(SCGCQ01436268)
- Add a new structure to provide OEMs ability to switch to select either I2C or PCIe as an out of band transport.(SCGCQ01445048)
- Provide OEMs ability to select either I2C or PCIe as an out of band transport.(SCGCQ01450245)
- Update description of MR_DCMD_CTRL_PERSONALITY_SET Dcmd.(SCGCQ01467149)
- Add support for API fields to report SED type of PD.(SCGCQ01587230)
- Add OnOff parameter in Properties2 of Structure MR_CTRL_PROP to enable/disable mix of Enterprise & Opal SED drives.(SCGCQ01593520)
- NVDATA parameter to OPAL SED.(SCGCQ01614689)
- Added a new interface between driver-aops to indicate if 64 bit SGL support is enabled.(SCGCQ01620350)
- Add new MFI Status to block requested operation due to existing controller configuration.(SCGCQ01670135)
- Change the mr.h API comment showing the new return status for the - MR_DCMD_PD_GET_INFO.(SCGCQ01670234)
- API change for Switch attached NVMe HW RAID support for Supermicro backplanes.(SCGCQ01697667)
- Request to enable JBOD for Rambler PNP ID.(SCGCQ01727448)
- Reverted the DDR tuning values.(SCGCQ01625968)
- Porting the changes of NVRAM_Struct from MesaVerde stream to 6.14.(SCGCQ01563144)
- Enhance Messaging Unit error ISR to dump debug information of virtual functions having error.(SCGCQ01553249)
- CacheCade: IO performance need to be improved for WB SVD and WB CCVD combination for specific PnP ID.(SCGCQ01472061)
- FW breaks into montaks with pinned cache and foreign configuration.(SCGCQ01403814)
- Boot message string change for BOOT_MSG_CACHE_DISCARD.(SCGCQ01394348)
- Block OCR after Clearing NVRAM.(SCGCQ01386919)
- PL 14.00.05.00 Integration with Invader MR 6.14.(SCGCQ01384265)
- Added MR_MFC_DEFAULTS.NVMeAbortTO and MR_MFC_DEFAULTS.NVMeMaxControllerResetTO.(SCGCQ01532045)
 FW to fail back host command for the wrong value.(SCGCQ01575960)
- Setting DDR flag for ROMB design having new DDR for an OEM.(SCGCQ01466802)


Version 24.21.0-0016 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE:  24.21.0-0016
BIOS:  6.36.00.1_4.19.08.00_0x06180202
UEFI Driver:  0x06180202
HII:  03.25.05.03
NVDT:  3.1705.00-0005
MR FW:  4.680.00-8258

Fixes:
 -  MR 6.13: Blocked Spin down Pass thru command for configured drives.(SCGCQ01201958)
 -  In RAID personality, MR_DCMD_CFG_AUTOCFG DCMD is disabled in non(SCGCQ01213915)
 -  Setting all the ldtoTgtId with 0xff beyond 240 entries.(SCGCQ01215003)
 - (SCGCQ01219438)
 -  MR_EVT_PD_ERROR_STATS events are logged when drive is moved to REBUILD/UNCONFIGURED BAD/ONLINE/OFFLINE. Also correct DCMD(SCGCQ01223284)
 -  FW crashes when FW update(OFU) is done with faluty onfi(SCGCQ01227115)
 -  Coverity issues:fixed the coverity defects.(SCGCQ01230560)
 -  Update the MAXTransferLength properly for Driver enabled 1MB support feature(SCGCQ01232275)
 -  Assertion failure in ../../dm/mpt2/mptrec.c at line 3139, while performing cable pull/push operation.(SCGCQ01235505)
 -  corrected the span index(SCGCQ01236287)
 -  Coverity issue 15748 and 17765(SCGCQ01241568)
 -  Drive Strength values are incorrect for last 8 phys of Red Brick Controller(SCGCQ01241680)
 -  Change Slew Rate on dual rank RedBrick Boards to fix ECC Errors.(SCGCQ01242817)
 -  Cache Data lost if power loss happens during descriptor preparation.(SCGCQ01253076)
 -  'C0:mr_wakeup: mem 45569e20, cache line ffffffff' observed while running BGI on RAID 5 Volume with media errors.(SCGCQ01256120)
 -  Assertion failure in ../../raid/2108vI2o.c at line 2398 on flashing firmware(SCGCQ01258563)
 -  Dev defect to address action items identified during Ventura(SCGCQ01260609)
 -  Dev defect to handle HW action items identified during Intruder(SCGCQ01261213)
 -  Cache data Lost when Term Log is set to "on"(SCGCQ01261426)
 -  6.13 ONFI_PORT: If power loss occurs after OCR, FW might lose tty log.(SCGCQ01262834)
 -  6.13_ONFI_PORT: Program the erase and wait count values during ONFI Initialization.(SCGCQ01262883)
 -  6.13 ONFI PORT :Set bit 0 in global Interrupt Register so that host will receive an interrupt.(SCGCQ01262884)
 -  Flash File System Reads fail after system reset.(SCGCQ01267220)
 -  FW does not remember user induced bad blocks across boots.(SCGCQ01267700)
 -  MR 6.13(SCGCQ01268066)
 -  Unable to access device PD (SSD)(SCGCQ01268412)
 -  MR_6.13:FW flash pack (SCGCQ01273216)
 -  Cache Restore fails if supercap is removed while cache offload is in Progress.(SCGCQ01274494)
 -  Unable to set termlog on/off from storcli intermittently on Intruder Armstrong board.(SCGCQ01278512)
 -  Storcli Failed to create single PD R0 from UGood drive which has replaced a UBAD foreign drive(SCGCQ01282181)
 -  Intruder : After Termlog Toggling with power cycle, result to ERROR: Dirty disk cache data has been lost(SCGCQ01282319)
 -  Modify Read Eye Training Algorithm to make it spec compliant.(SCGCQ01283719)
 -  High DB and Log write(SCGCQ01285311)
 -  Coverity reported an uninitialized variable(SCGCQ01285595)
 -  OS hung and iMR FW reset when do delete and create VD from previous powersave PD (Spindowned)(SCGCQ01287286)
 -  Reboot the system with 240 R0 Volumes and changing the mode(SCGCQ01288297)
 -  PL Fault 0000601e observed while running multipath on/off script in JBOD mode.(SCGCQ01288781)
 -  erase types and startSecureEraseNonSED is set accordingly(SCGCQ01289147)
 -  Modify NVDATA boot message to rename 'NVDATA image' to 'firmware image'(SCGCQ01290201)
 -  Cache data lost event seen for WT vds(SCGCQ01313607)
 -  Kill adapater observed while running IO's on 240 Volumes(SCGCQ01313950)
 -  Coverity: Fixing Coverity defect 16148(SCGCQ01316152)
 -  Fixing the coverity raised issue(SCGCQ01318465)
 -  Coverity issue 19341(SCGCQ01319291)
 -  HW workaround implementation for SCGCQ00830272 and SCGCQ01048567(SCGCQ01323607)
 -  auto config is not happening in some cases after issuing storcli /cx set autopdcache=r0(SCGCQ01323848)
 -  MR 6.14 Beta: MonTask: line 245 in file ../../raid/1078int.c while running reboot test with background operations(SCGCQ01332706)
 -  MR_6.14: Intruder PCI Trapping ISR incorrect logic for config trap address(SCGCQ01332947)
 -  ntruder: Fix the Intruder Boot Block compilation and warning issue.(SCGCQ01334292)
 -  Imr Invader FW crashes while upgrading from Pkg 24.18.0(SCGCQ01342601)
 -  No amber LED when a configured disk is removed(SCGCQ01343017)
 -  Controller fails to boot up when migrated from 6.13 to 6.14 FW for Specific OEM(SCGCQ01348114)
 -  Value defined for the DDR turning parameter DP_IO_VREF_1_2 is wrong for invader boards(SCGCQ01350295)
 -  MR_INVADER_WORKAROUND_PCIE_IGNORE_REPLY_PARITY_ERROR macro definition missing(SCGCQ01351483)
 -  Intruder 4G DDR tuning value has to be changed in MR FW.(SCGCQ01368845)
 -  Lenovo Sebastian Fatal Firmware error when connecting to straight without Group ID support.(SCGCQ01204592)
 -  FW does not fail unsupported erase type for a PD(SCGCQ01221549)
 -  Allow Cyrpto erase on non(SCGCQ01222318)
 -  Fix coverity reported issue(SCGCQ01227079)
 -  FW is not updating EPDs list exposed to host after drives removal event is posted which is causing dev nodes are not getting deleted on drive removal(SCGCQ01230441)
 -  Diagnostics report of iMR Invader contains information about R6 and R60 is set to 0(SCGCQ01235661)
 -  Enable MR_DCMD_PD_ERROR_STATS and the event MR_EVT_PD_ERROR_STATS only for direct attached drives(SCGCQ01237252)
 -  DATA TLB ERROR, While connecting controller each Port to Back(SCGCQ01252111)
 -  MR 6.13.1Alpha:Probable Drive/cable issue Event not printed in firmwarelogs on triggering drive/cable error when connected BP(SCGCQ01256005)
 -  Handling of DCR errors in MSS core(SCGCQ01263110)
 -  Controller does not boot up while performing cache offload .(SCGCQ01278480)
 -  Controller cache discarded due to memory/battery problem(SCGCQ01280181)
 -  Perf(SCGCQ01283507)
 -  Code review: turn off the onfi when bbu is bad(SCGCQ01297565)
 -  Coverity issues 19244, 19245, 19246 and 19248(SCGCQ01299214)
 -  MR 6.14 Intruder(Vail): Intruder Controller hangs in primary core on reboot in Dell Power Edge T620 server.(SCGCQ01299482)
 -  Fix coverity issue 19253 Structurally dead code in checkCacheOffloadStatus, raid/1078init.c(SCGCQ01300678)
 -  coverity defects fixed(SCGCQ01300689)
 -  To fix coverity issue 17759(SCGCQ01317039)
 -  Found invalid event(SCGCQ01347858)
 -  Placement of an image checkword at data area of NOR flash leads to controller crash(SCGCQ01375071)
 - (SCGCQ01227044)
 -  FC: 0 CS: 0 offload meta signature not valid, ffffffff observed in FW logs on a system restart.(SCGCQ01299424)
 -  MR 6.14 (SCGCQ01300667)
 -  Coverity issue 15356(SCGCQ01301658)
 -  update the boundary values in UpdateFeatureSetValues()(SCGCQ01209605)
 -  FW hang finaly leading to kill adatper with inBox driver(SCGCQ01250342)
 -  MR7.1_NVMe: After foreign import of 64 R0 VDs, operating system unable to discover the VDs(SCGCQ01229929 Port Of SCGCQ01209394)
 -  FW crashes when FW update(OFU) is done with faluty onfi(SCGCQ01235056 Port Of SCGCQ01227115)
 -  Server (Purley): Controller (16i) (SCGCQ01235753 Port Of SCGCQ01200311)
 -  In RAID personality, MR_DCMD_CFG_AUTOCFG DCMD is disabled in non(SCGCQ01237142 Port Of SCGCQ01213915)
 -  Storcli failed to stop drives LED locating with a range(SCGCQ01241870 Port Of SCGCQ01051728)
 -  MR7.1_NVMe: After foreign import of 64 R0 VDs, operating system unable to discover the VDs(SCGCQ01242766 Port Of SCGCQ01209394)
 -  unable to encrypt disk when using no pass(SCGCQ01245596 Port Of SCGCQ01144752)
 -  Offline Marked DG (RAID0) appearing in RHEL 7 install(SCGCQ01245782 Port Of SCGCQ00995384)
 -  SAS2208 card reset in DataCenter due to unknown reason(SCGCQ01247264 Port Of SCGCQ01240574)
 -  RDM in Use(SCGCQ01255837)
 -  ONFI: To properly handle the OCR case with RESET Status Register.(SCGCQ01259337 Port Of SCGCQ00665475)
 -  ONFI BBLIST:ONFI BadBlocks: COL disarmed, VDs remain in WB mode, no Administrative Messages to bad flash part.(SCGCQ01260470 Port Of SCGCQ01235856)
 -  Firmware halts upon changing controller personality to JBOD mode with MCTP enabled(SCGCQ01260889 Port Of SCGCQ01252243)
 -  Infinite loop in onfiSyncModeEnter(SCGCQ01260995 Port Of SCGCQ00329024)
 -  FW crashes when setting fwtermlog bbu=on to a card with bad NAND flash(SCGCQ01261425 Port Of SCGCQ01129530)
 -  Insertion of the boot messages and the evets for montoring the ONFI backup capacity.(SCGCQ01263212 Port Of SCGCQ00433463)
 -  'C0:mr_wakeup: mem 45569e20, cache line ffffffff' observed while running BGI on RAID 5 Volume with media errors.(SCGCQ01263800 Port Of SCGCQ01256120)
 -  Handling of DCR errors in MSS core(SCGCQ01263859 Port Of SCGCQ01263110)
 -  Invalid date for next learn cycle is set due to invalid date from OEM server (STF: Next learn time is 1970(SCGCQ01264476 Port Of SCGCQ01152321)
 -  GetAllLDAllowedOperation call in Storelib is not returning Allowed operations when some LDs are deleted(SCGCQ01265445 Port Of SCGCQ01250559)
 -  FD33xD issues in VMWare(SCGCQ01266300 Port Of SCGCQ01203008)
 -  In RAID personality, MR_DCMD_CFG_AUTOCFG DCMD is disabled in non(SCGCQ01274496 Port Of SCGCQ01213915)
 -  MR_6.13:FW flash pack (SCGCQ01280567 Port Of SCGCQ01273216)
 -  unable to encrypt disk when using no pass(SCGCQ01287082 Port Of SCGCQ01144752)
 -  Controller cache discarded due to memory/battery problem(SCGCQ01288848 Port Of SCGCQ01280181)
 -  RAID10 VD goes to failed state after performing RLM(SCGCQ01289123 Port Of SCGCQ01277951)
 -  IN FAILED ARRAY bit is not being set when a VD is cleared(SCGCQ01289194 Port Of SCGCQ01137359)
 -  Storcli Failed to create single PD R0 from UGood drive which has replaced a UBAD foreign drive(SCGCQ01290418 Port Of SCGCQ01282181)
 -  RAID10 VD goes to failed state after performing RLM(SCGCQ01291340 Port Of SCGCQ01277951)
 -  Controller cache discarded due to memory/battery problem(SCGCQ01291492 Port Of SCGCQ01280181)
 -  Cannot stop patrol read on PD with medium errors by the stop cmd(SCGCQ01294884 Port Of SCGCQ01063103)
 -  Perf(SCGCQ01297497 Port Of SCGCQ01283507)
 -  Code review: turn off the onfi when bbu is bad(SCGCQ01297666 Port Of SCGCQ01297565)
 -  Code review: turn off the onfi when bbu is bad(SCGCQ01299260 Port Of SCGCQ01297565)
 -  Perf(SCGCQ01300759 Port Of SCGCQ01283507)
 -  PL Fault 0000601e observed while running multipath on/off script in JBOD mode.(SCGCQ01304919 Port Of SCGCQ01288781)
 -  Firmware:(SCGCQ01306491 Port Of SCGCQ01258853)
 -  6.14 : To fix IOPATH overflow during linking(SCGCQ01311731 Port Of SCGCQ01311464)
 -  Unable to access device PD (SSD)(SCGCQ01321307 Port Of SCGCQ01268412)
 -  OS hung and iMR FW reset when do delete and create VD from previous powersave PD (Spindowned)(SCGCQ01326069 Port Of SCGCQ01287286)
 -  HW workaround implementation for SCGCQ00830272 and SCGCQ01048567(SCGCQ01326394 Port Of SCGCQ01323607)
 -  B200M4 (Carmel/ 3108 iMR): driver crashed after FW update via UCSM (UCSM bundle 2.2(8fS2)A/B to 3.1(2.163)A/B)(SCGCQ01331892 Port Of SCGCQ01271186)
 -  B200M4 (Carmel/ 3108 iMR): driver crashed after FW update via UCSM (UCSM bundle 2.2(8fS2)A/B to 3.1(2.163)A/B)(SCGCQ01332726 Port Of SCGCQ01271186)
 -  MR 6.14 Intruder(Vail): Intruder Controller hangs in primary core on reboot in Dell Power Edge T620 server.(SCGCQ01334334 Port Of SCGCQ01299482)
 -  MR_6.14: Intruder PCI Trapping ISR incorrect logic for config trap address(SCGCQ01334365 Port Of SCGCQ01332947)
 -  MR 6.14 Beta: MonTask: line 245 in file ../../raid/1078int.c while running reboot test with background operations(SCGCQ01339330 Port Of SCGCQ01332706)
 -  Cache data lost event seen for WT vds(SCGCQ01349420 Port Of SCGCQ01313607)
 -  Kill adapater observed while running IO's on 240 Volumes(SCGCQ01350347 Port Of SCGCQ01313950)
 -  No amber LED when a configured disk is removed(SCGCQ01350771 Port Of SCGCQ01343017)
 -  Firmware hits montask while reconstruction when drive is pulled out(SCGCQ01351442 Port Of SCGCQ01260340)
 -  MR 6.13: Blocked Spin down Pass thru command for configured drives.(SCGCQ01351559 Port Of SCGCQ01201958)
 -  IOMMU fault at address 0x80360000(SCGCQ01356192 Port Of SCGCQ01279547)
 -  LSA hangs when user try to change drive security key.(SCGCQ01367331 Port Of SCGCQ01342655)
 -  Invalid date for next learn cycle is set due to invalid date from OEM server (STF: Next learn time is 1970(SCGCQ01241869 Port Of SCGCQ01152321)
 -  MR6.12 NVRAM Overflow (SCGCQ01248969 Port Of SCGCQ01230749)
 -  FD33xD issues in VMWare(SCGCQ01261095 Port Of SCGCQ01203008)
 -  FD33xD issues in VMWare(SCGCQ01263759 Port Of SCGCQ01203008)
 -  Configuration lost and system crashed on having a stale configuration connected(SCGCQ01273187 Port Of SCGCQ01170701)
 -  PL Fault 0000601e observed while running multipath on/off script in JBOD mode.(SCGCQ01304921 Port Of SCGCQ01288781)
 -  FC: 0 CS: 0 offload meta signature not valid, ffffffff observed in FW logs on a system restart.(SCGCQ01351052 Port Of SCGCQ01299424)
 -  Controller fails to boot up when migrated from 6.13 to 6.14 FW for Specific OEM(SCGCQ01351614)
 -  SAS2208 card reset in DataCenter due to unknown reason(SCGCQ01311439 Port Of SCGCQ01240574)
 -  Drive Strength values are incorrect for last 8 phys of Red Brick Controller(SCGCQ01247082 Port Of SCGCQ01241680)
 -  Firmware hits montask while reconstruction when drive is pulled out(SCGCQ01282285 Port Of SCGCQ01260340)
 -  Code review: turn off the onfi when bbu is bad(SCGCQ01299219 Port Of SCGCQ01297565)
 -  Controller does not boot up while performing cache offload .(SCGCQ01288845 Port Of SCGCQ01278480)

 
Enhancements:
 -  New fault code for routine synchronous reset(SCGCQ01264142)
 -  Vail FW not responding to PWR_REQ in time. Request to up the number of TURs sent before timing out drive.(SCGCQ01373161)
 -  Disable OOB communication via I2C(SCGCQ01369359)
 -  Integrate Intruder PL 14.00.04.00 with MR 6.14(SCGCQ01341925)
 -  PL phase 13.0007.00 integration with MR 6.13(SCGCQ01334112)
 -  PL integration(SCGCQ01330898)
 -  Integrate PL phase 14.00.02.00 with MR 6.14(SCGCQ01307233)
 -  Integrate 13.00.06.00 PL to MR 6.13(SCGCQ01304141)
 -  PL integration 12.00.10.00 with MR 6.12(SCGCQ01276465)
 -  Integrated PL 12.0.9.0 with MR 6.12(SCGCQ01268897)
 -  Shift IOPATH code by 4 cache lines to workaround intruder performance issue.(SCGCQ01262698)
 -  PR State Machine Clean up during Patrol Read/Check Consistency Conflicts(SCGCQ01260431)
 -  Integrate intruder PL 13.00.04.00 (SCGCQ01237533)(SCGCQ01238286)
 -  Integrate PL 13.00.04.00 to MR_FW_SAS3_6.13_4G_DDR(SCGCQ01238126)
 -  Open up MR_DCMD_CFG_AUTOCFG for iMR for GET operation(SCGCQ01228949)
 -  Customer requesting digitally signed FW packages on their Intruder controller(SCGCQ01215397)
 -  MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP(SCGCQ01180886)
 -  MPI 2.5: Add two new reason codes to Active Cable Exception Event Data(SCGCQ01208954)
 -  MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0(SCGCQ01213028)
 -  MPI 2.6: Add new firmware download type (CBB BACKUP)(SCGCQ01258005)
 -  MPI 2.6: Device side PCIe SRNS flag(SCGCQ01276256)
 -  MPI 2.6: Add new firmware download type (CPLD IMAGE)(SCGCQ01305760)
 -  IN FAILED ARRAY bit is not being set when a VD is cleared(SCGCQ01137359)
 -  Integrate Intruder PL 13.00.05.00 (RO SCGCQ01263844)(SCGCQ01265401)
 -  Add additional sense data to firmware tracker list(SCGCQ01254954)
 -  Method for determining bad ONFI flash via Storcli & SNMP trap upon NAND flash failure for Aspen and Vail (Invader and Intrude(SCGCQ01219862)
 -  MPI2.6: Mfg7 support for arbitrary starting slot number(SCGCQ01213267)
 -  MPI 2.6: Add Aero PCI Device IDs(SCGCQ01373008)
 -  Isolating faulty cable issue from bad drive issue(SCGCQ01215270)
 -  PL integration(SCGCQ01268896)
 

Version 24.18.0-0046-1 - Moderate Impact/Low Probability of Occurrence
--------------------
BIOS:  6.34.01.0_4.19.08.00_0x06160201
UEFI Driver:  06160201
HII:  E3.23.06.04
NVDT:  3.1611.00-0012
MR FW:  4.670.00-8194
Package: 24.18.0-0046 

- Removed support update via ThinkSystem XClarity Control (XCC) web GUI and Lenovo XClarity Essentials OneCLI -imm option


Version 24.18.0-0046 - New Function Only/No fixes
--------------------
BIOS:  6.34.01.0_4.19.08.00_0x06160201
UEFI Driver:  06160201
HII:  E3.23.06.04
NVDT:  3.1611.00-0012
MR FW:  4.670.00-8194