Lenovo Storage Host-Bus-Adapter (HBA) Firmware

Change History

ThinkSystem 440-x SAS/SATA 12Gb HBA Firmware and BIOS Update

Supported Adapters:  
	ThinkSystem 440-16e SAS/SATA PCIe Gen4 12Gb HBA for 4Y37A09724
	ThinkSystem 440-16i CFF SAS/SATA PCIe Gen4 12Gb Internal HBA for 4Y37A09725
	ThinkSystem 440-8i SAS/SATA PCIe Gen4 12Gb HBA for SR17A98375
	ThinkSystem 440-16i SAS/SATA PCIe Gen4 12Gb HBA for SR17A98376
    ThinkSystem 440-8e SAS/SATA PCIe Gen4 12Gb HBA for 4Y37A78837
			 

NOTE TO SERVICE - Reference RETAIN #N/A

Version 31.125.07.00
---------------
    BIOS            Firmware      UEFI Driver   
 9.61.00.00     31.00.00.00       31.00.00.00

Defects:
-[9500] SAS_IO_UNIT_CONTROL/SEND_PRIMITIVE command fails for the phys with PCIe support enabled.(DCSG01467130)
-Correct the routing of Led Data output based on the selected GPIO..(DCSG01633536)
-Drives are marked as Unconfigured Bad in 9540 controller during the hot-plug test..(DCSG01528863)
-Values in Manufacturing Page 57 fields were not correct.(DCSG01651949)
-NVMe: a certain NVMe 2.0 device fails to initialize.(DCSG01547099)
-Observed hang in SAS only and NVMe only mode in 3808N controller after adapter reset..(DCSG01508452)
-UseIdleSas12G was not set in Hardware even when it was set in the ExtManPage40.(DCSG01517111)
-PL Firmware : SAS Phy Page 0 is not showing correct values when vses disabled.(DCSG01496873)
-UBM BST: Scrutiny command fails during VSES Instance test.(DCSG01388814)
-(NVMe Only): Ensure NVMe drive limits are not overridden by NVData.(DCSG01684592)
-BST: scripts de-allocate drive objects after every device scan.(DCSG01467893)
-Invalid Enclosure ID was observed when NVMe drive was hotplugged to 9580 card.(DCSG01550785)
-Bitwise operation doesn't give expected result.(DCSG01680369)
-NVMe Only): Invalid verification length was not returning check condition.(DCSG01669988)
-When Verify command to NVMe drive was aborted, resource Mid was not freed.(DCSG01658338)
-Direct attached Lane break test failed on Gen4 NVMe U.2 drive.(DCSG01556638)
-ddrlib RL data eye analysis debug print typo.(DCSG01373989)
-(NVMe Only) Maximum Write same Length should be 64 bit field in 'Manufacturing Page 57' of NVData.(DCSG01685540)
-Use Direct GPIO LED management if the 3808N Device LED Management policy is set..(DCSG01576748)
-94xx/95xx PL Spinup: Incorrect write to register to clear the spinup interrupt.(DCSG01521501)
-9500 Series: Fault 0x5805 Invalid Message Frame Index Seen after multiple resets.(DCSG01516095)
-SCSI NVMe Translation Layer: MID resource usage for Verify Command.(DCSG01655177)
-Backend PCIe: ED91 fault on hot reset.(DCSG01520805)
-BMC reset in a loop leads to controller not being detected through MCTP over I2C.(DCSG01460317)
-Continuous MCTP command failure with a bad drive in topology leads to controller not being detected through MCTP.(DCSG01516217)
-PL: Firmware failed assertion check for some NVMe drive models.(DCSG01571116)
-[9500 BST] Update OEM BST servers connection settings in BST scripts.(DCSG01580444)
-BST: UART thread slows down the execution of BST scripts.(DCSG01468544)
-Build all failed on firmware int code.(DCSG01538008)
-Read(32) or Write(32) CDB sent to NVMe drive reported incorrect additional sense code.(DCSG01546839)
-[95xx] NVMe Drive firmware update failed if the drive firmware payload size is more than 2Mb and 32k aligned.(DCSG01531437)
-(NVMe Only): Fault 0x6001 was observed for verify(16) command sent to drive.(DCSG01667121)
-Host boot failure caused a UEFI hang on some systems.(DCSG01562181)
-Fix 'Static Analysis Tool' reported items in Firmware.(DCSG01571779)
-Controller firmware faults with fault code 0xD20F during system reboot test.(DCSG01635232)
-95XX card: When JBOD Expanders are periodically reset, drive in a large topology may go missing.(DCSG01592213)
-(NVMe Only): verify command did not return correct sense information.(DCSG01672961)
-Build all failed on firmware int code.(DCSG01571899)
-Non 512 Mutiple ReportZone request cause 0 data transfer but completes successfully.(DCSG01467889 (Port Of Defect DCSG01481561))
-Task Management fail after cable pull with large topology.(DCSG01597290 (Port Of Defect DCSG01611169))
-MSS lib update to reflect Extended Temp Range and Temp Controller Refresh removal.(DCSG01560670 (Port Of Defect DCSG01562699))
-VSES Commands hung during the drive pull test with IOs..(DCSG01480400 (Port Of Defect DCSG01496941))
-Cable management diagnostic command shows incorrect data for some cables.(DCSG01427369 (Port Of Defect DCSG01451464))
-SATL UNMAP command with parameter list 6 returns wrong Additional sense.(DCSG01660851 (Port Of Defect DCSG01661540))
-Firmware crashes when reading the UBM controller information when the UBM controller is in non operational mode..(DCSG01507596 (Port Of Defect DCSG01518264))
-Pulling low power mode NVMe drive causes PL Fault.(DCSG01542341 (Port Of Defect DCSG01550340))
-Overnight reading the snapdump OnDemand in a loop, caused iMR Controller not found error.(DCSG01470476 (Port Of Defect DCSG01496925))
-Virtual SES IOs aren't failed if a UBM I2C transfer error occurs during LED update.(DCSG01486559 (Port Of Defect DCSG01487551))

EnhancementRequests:
-Updated 'Summary Release Notes' document.(DCSG01521495)
-List down the Third Party Licenses used in Firmware.(DCSG01629211)
-[BST] SATL command inclusion, enhancement of NON read/write command verification.(DCSG01372968)
-BST: Remove NVMe verify command from Invalid Command List.(DCSG01658892)
-Add functionality to generate shmoo plots in DDR library.(DCSG01587288)
-Power customization support for SAS3808N board..(DCSG01453955)
-[BST] Include SATL commands - Format Unit command (04h) and Security Protocol Out (B5h) command.(DCSG01372971)
-Updated Firmware to support SCSI to NVMe Translation Spec 1.10.(DCSG01521548)
-Firmware support for SCSI NVMe Translation Layer Specification version 1.14.(DCSG01611691)
-[95xx] Added feature to override the firmware control of PERST# signal to NVMe drives using NVDATA.(DCSG01421204)
-Block the access to disabled Hardware cores on 3808N adapter while dumping pl dbg..(DCSG01515787)
-[BST] OEM server BST bring-up with 9500 HBA.(DCSG01301718)
-Firmware: Ensure that IT firmware can not run on the 3808N.(DCSG01494307)
-Add new chip entry for 3808N controller..(DCSG01512905)
-PL support for Direct GPIO LED management..(DCSG01494319)
-Add support for OEM Backplanes.(DCSG01418256)
-Add UBM emulator test cases - Part 1.(DCSG01373023)
-Update NVDATA Major Version for Ph30.(DCSG01588354)
-[9500 BST] OEM BST server APC ip details update.(DCSG01472729)
-BST scripts were updated for 9300 series card setup.(DCSG01652453)
-Make Temp Controlled Refresh (TCR) configurable in DDR library..(DCSG01604054)
-BST: Added NVMe test for SCSI Immediate Command translation.(DCSG01372972)
-UBM emulator BST improvements.(DCSG01413397)
-Added Serdes Config Parameters to ExtManPage40.(DCSG01508464)
-[95xx] Reduction in default maximum resource count values in Runtime Configuration Parameters for Enclosures and.(DCSG01443947)
-Added duplicate MID protection support to multi-LUN drives.(DCSG01309777 (Port Of EnhancementRequest DCSG01536664))
-NVDATA switch to enable the PDB0B core for 3808 N controller.(DCSG01551132 (Port Of EnhancementRequest DCSG01556364))
-NVMe: handle vendor specific failure condition.(DCSG01533800 (Port Of EnhancementRequest DCSG01536830))
-PL Firmware: Bring up of OEM specific EDSFF UBM Backplane.(DCSG01467248 (Port Of EnhancementRequest DCSG01498560))
-3808N: Power customization for Generic and OEM specific profiles.(DCSG01537426 (Port Of EnhancementRequest DCSG01550354))


Version 27.125.09.00
---------------
    BIOS            Firmware      UEFI Driver   
  9.53.00.00      27.00.00.00    27.00.00.00

Defect:
-Possible division or modulo by zero in enclosure management code..(DCSG01224310)
-[Code Coverage] SCSI to NVMe translation test failed in BST.(DCSG01252405)
-9500-16i - The C_TYPE sideband signals of the connector are not driven to Low.(DCSG01379243)
-Build all failed on firmware tip code.(DCSG01343959)
-SPILIB2: SPI Emulation Erases the wrong section.(DCSG01049441)
-HBA discovery failed with Phase 24 Storelib and StorelibTest.(DCSG01207008)
-SPILIB2: Fix offsets in SPI2_LIB_DEVICE_PARAMS.(DCSG00428841)
-[SATA Only] NCQ Errors observed with running Read/Write IOs along with SCSI Unmap.(DCSG01254091)
-Firmware reports dual ports for SATA drives..(DCSG01352291)
-Variable type, Pointer is used as argument to sizeof function in SCSI to NVMe translation for complete log sense handler.(DCSG01385273)
-SAS drive keeps failing SCSI TUR with Check condition due to Controller not sending Periodic Notify (Enable Spinup.(DCSG01232852)
-Firmware was not repairing an NVMe drive with detached Inactive Namespace..(DCSG01321255)
-Wrong expected sense data in invalid CDB test for NVMe drive.(DCSG01252944)
-Hardware Workaround:Link between Controller and expander not always recovering after link reset.(DCSG01196230)
-Disable SATA protocol when in optical mode.(DCSG01194126)
-Locate LED operation does not work for NVMe drive slot on UBM backplane.(DCSG01230479)
-Same slot number is assigned to x1 link width drives connected to consecutive controller PHYs when an I2C backplane detection.(DCSG01375808)
-Firmware is not incrementing the DFC Change Count value when there is a DFC change detected by the firmware..(DCSG01287092)
-SPILIB2 : Watchdog reset due to ARM Exception while flash under stress.(DCSG00814654)
-9500 Series- host with eight PHY controller hangs during warm reboot.(DCSG01289054)
-[Aero/Ventura] Add check for Sense Data size.(DCSG01178348)
-Build all failed on firmware tip code.(DCSG01381053)
-LBA information missing from sense data with Medium Error Sense Key for SATA drives.(DCSG01183332)
-SPILIB2: Series 9700 Chip Select Timing registers default to zero.(DCSG01182027)
-[BST] "Invalid SCSI CDBs" test failed for NVMe Format unit commands in older firmware versions.(DCSG01287310)
-Uninitialized scalar variable access in UBM Backplane management and I2C driver code..(DCSG01339421)
-NVMe device connected to PCIe switch is not discovered by controller firmware on boot up.(DCSG01260624)
-NVMe Encapsulated MPI command not failed when it is blocked by IO Unit Page 13..(DCSG01294635)
-SPILIB2: (Margay Only) ARM Exception while flash under stress upon closing telnet.(DCSG00914933)
-Firmware console command 'pl eminfo' shows no PCIe support for a PCIe supported UBM backplane Device Face Connector.(DCSG01285442)
-IT controller firmware sending MCTP version numbers in reverse order.(DCSG01234654)
-Aero: Incorrect topology phys memory allocation.(DCSG01185588)
-Uninitialized pointer access in UBM Backplane management code.(DCSG01225064)
-Reading IO Unit Page 13 returns junk data.(DCSG01292339)
-Build all is failed due to Error: NVDATA Major Versions do not match!.(DCSG01258017)
-C0:[141]:[Error] Signing Buffer Failed Sts:2 mesg after import successfully the certificate and reboot.(DCSG01270486)
-Self test aborts when Open Zone command issued on a Security locked drive.(DCSG01194141)
-observed when diagnostic register dump is performed while running IO to the drives. Description Of Removed RxEEDP Buffer dump from the diagnostic register dump..(DCSG01227332)
-[NVMe] Mode F Firmware download to certain NVMe drives fails..(DCSG01286617)
-[Code Coverage] NVMe stress test - NVMe PRP Firmware validation.(DCSG01260284)
-BST script failed to invoke utilities.(DCSG01357327)
-Io Unit Control with Remove device fails if MPI function blocking is enabled. IO Unit Page 13 is writeable..(DCSG01270812)
-Phase 24 Code analysis tool Defects related to SPDM.(DCSG01224346)
-Target mode controller port width degrades following host resets/power cycles with autoport config disabled.(DCSG01325599)
-[SATA] SATA Initialization fails on certain large capacity SATA drives.(DCSG01194600)
-Firmware summary notes needs to be updated to remove 94xx boards references.(DCSG01271551)
-QErr value in Control mode page for NCQ SATA devices is set to 0 instead of 1.(DCSG01375632)
-Erase operation fails on OEM specific UBM backplane during UBM controller firmware update.(DCSG01289710 (Port Of Defect DCSG01294066))
-[NVMe] Some NVMe drives do not link up on certain OEM backplanes..(DCSG01193134 (Port Of Defect DCSG01196465))
-Direct attached devices do not link up in case SEP backplane detection is configured in NVData.(DCSG01285763 (Port Of Defect DCSG01286648)
-Revert SATA Init timeout changes.(DCSG01252414 (Port Of Defect DCSG01255751)
-Change spinup mode while SATA link rese.(DCSG01161733 (Port Of Defect DCSG01231494))
-Update NVDATA Major version.(DCSG01258013 (Port Of Defect DCSG01270040))
-Sanitize (Block Erase) along with shutdown sequence caused assertion in firmware. (NVMe Only).(DCSG01358573 (Port Of Defect DCSG01371174))
-IOC Page 7 does not report the updated "SASNotifyPrimitiveMasks".(DCSG01220829 (Port Of Defect DCSG01222353))
-SATA, Fault 0x5919 seen during write same error and task managements.(DCSG01176562 (Port Of Defect DCSG01228270))
-M.2 NVMe drive initialization failed after warm reset.(DCSG01264359 (Port Of Defect DCSG01301951))
-[VSes] Number of slots reported incorrectly in certain OEM backplane.(DCSG01200427 (Port Of Defect DCSG01215896))
-NVDATA major version was updated to be same as Phase Version.(DCSG01477125)
-95xx]: Log sense page 0x15 fails on ACS-5 supported SATA drive..(DCSG01458189)
-PL firmware not failing NVMe self-test when already an existing NVMe self-test command.(DCSG01459189 (Port Of Defect DCSG01350001))
-SCSI Self-Test Results (0x10) log page not updating status when self-test in progress.(DCSG01466802 (Port Of Defect DCSG01072582))
-[9500 BST] Reading the Backplane FRU data causing the NVMe drive link to go down fo.(DCSG01420775)
-[95xx]: Incorrect slot number management for non-UBM backplanes.(DCSG01451450)
-A target reset Task Management to a direct attach SAS drive may not go out to the drive even.(DCSG01432770 (Port Of Defect DCSG01419839)
-EDSFF drive in UBM will not link up and Change Detect polling may not happen for some.(DCSG01417264)
-[95xx] - Slot numbering for NVMe devices connected behind an invalid backplane shown.(DCSG01442157 (Port Of Defect DCSG01436490))
-[9500/02] Update Combo Serdes Wrapper M0 code.(DCSG01431077)
-BST: Added NVMe test for SCSI Immediate Command translation.(DCSG01372972)
-Support generation code feature in MPI SEP request handler.(DCSG01420969 (Port Of EnhancementRequest DCSG01417694))
-Map valid slots to its corresponding element index in subsequent MPI SEP request.(DCSG01420988 (Port Of EnhancementRequest DCSG01418309))


EnhancementRequests:
-Add IO Unit page 13 handling to Block/Allow MPI functions.(DCSG01214245)
-Implement incomplete firmware handlers for the SCSI commands as per the latest.(DCSG01308277)
-SPILIB2: Add support for high impedance dummy cycles in 9700 Series.(DCSG01118681)
-BST bring up on Windows server.(DCSG00021431)
-SPILIB2: Add support for new Cypress parts via proprietary CFI Method.(DCSG00734502)
-Updated setup hardware configuration in BST scripts.(DCSG01352775)
-SPILIB2: Add support for bulk erase.(DCSG01061535)
-Updated release scripts for verifying Firmware build status.(DCSG01350607)
-SPILIB2: Update python decoder with latest fixes.(DCSG01091175)
-Firmware: Implement REFCLK control in HII.(DCSG01291368)
-SPILIB2: Configure Series 9700 NVSRAM hardware to send Write Enable on first.(DCSG01131779)
-IT NVDATA: Update phase 26 NVDATA major version.(DCSG01386930)
-[SNTL] Update SCSI Format Translation for NVMe devices.(DCSG01137935)
-SPILIB2: Add new configuration bits to the init interface for SPI Flash drive strength.(DCSG01015117)
-Aero - SecureBoot: Added debug messages to the ring-buffer when the FW download.(DCSG01132478)
-Aero FW-Download: when writing bootloader to the main region, write the signature.(DCSG01154887)
-SPILIB2: Add MRAM and optional parameters file to CVS decoder.(DCSG01128295)
-SPILIB: Add support for Hybrid topology CFI parts.(DCSG00782279)
-Discontinue Firmware Release for 94xx Series of chips.(DCSG01240537)
-SPILIB2: Add serial mode support for SPI devices with read only Quad Enable bits.(DCSG00916467)
-PL Firmware: SFF-TA-1005 Version 1.4 Support.(DCSG01214256)
-BST bring up on Linux server.(DCSG01267771)
-Update createSasversion.exe to use getCreds.(DCSG00131581)
-Updated Package build option in release scripts.(DCSG01360774)
-SPILIB2: Eliminate incompatible erase commands in MultiErase mode.(DCSG00830450)
-Code Coverage] Additional SCSI to NVMe translation tests in BST scripts.(DCSG01142852)
-SPILIB2: Support for Additional SPI Clock Frequencies.(DCSG00424412)
-SPILIB2: Support ECC for Margay.(DCSG00429625)
-SPILIB2: 9700 Series core needs maximum continuous count initialized earlier.(DCSG01170965)
-Firmware: Support Long Lock Delay Times when Negotiating to a 6G SATA Driv.(DCSG01253833)
-SPILIB: Add Python-Based Logic Analyzer Decoder.(DCSG00980221)
-SPILIB2: Add support for serial mode for parts with QE=1 and dual mode support.(DCSG00831421)
-Use event based wait for browser automation during release process.(DCSG01133010)
-Upgrade ARM compiler version.(DCSG01331364)
-SPDM library: Add support for SPDM v1.0.(DCSG01137730)
-SBLIB: Clean up code for external use.(DCSG01150489)
-Update SB Lib to latest.(DCSG01224363)
-SPILIB2: Update Series 9700 SPI headers to latest.(DCSG01132011)
-SPILIB2: Port all changes AV1 to AV2 for manual access files.(DCSG00917802)
-SPILIB: Update Series 9700 header file.(DCSG01117315)
-Firmware: Enhanced NVMe Recovery Process.(DCSG01220515)
-Add ApSHA changes.(DCSG01209350)
-SPDM: Upgrade the latest SPDM Library in PH26.(DCSG01219141)
-SPILIBAV2: Misc. updates to Avenger2 SPI code for FPGA.(DCSG01057329)
-Update SPI Lib to latest.(DCSG01215946)
-[Code Coverage] Include CTC files in firmware code and create a build type that.(DCSG01132120)
-SPILIB: Update build scripts for ADS.(DCSG00943761)
-SPILIB2: Add High Level SPI Emulation Library.(DCSG00508974)
-PL firmware workaround for UBM Backplane firmware flashing issue in OEM specific.(DCSG01237118 (Port Of EnhancementRequest DCSG01252393)
-PL: Enable the UBM firmware update support for OEM specific UBM backplane.(DCSG01233264 (Port Of EnhancementRequest DCSG01252355))
-IOP: Rework MCTP packet validation code for workaround for some multi-segment.(DCSG01289379 (Port Of EnhancementRequest DCSG01328386))
-9500] Add support for host phys/lanes in Port Status Green GPIO.(DCSG01207029 (Port Of EnhancementRequest DCSG01251940))
-Add support for new product specific MCTP Event.(DCSG01149990 (Port Of EnhancementRequest DCSG01268764)
-Add support for OEM specific SAS 4 expander based enclosure with 950x controllers.(DCSG01351490 (Port Of EnhancementRequest DCSG01363691))
-LCS work around in PL firmware to be made generic for all models of an OEM specific UBM.(DCSG01452718 (Port Of EnhancementRequest DCSG01446403))
-BST: Added NVMe test for SCSI Immediate Command translation.(DCSG01372972)
-Update Secure boot Library in Firmware.(DCSG01445968)
-Buffer overrun on Request Sense to an NVMe device.(DCSG01428721 (Port Of Defect DCSG01425345)
-[HBA 95xx]: Set LSI-bit to one in the Device info field for Broadcom expander device type.(DCSG01418828)
-[9500 PL] Spinup handling when rising edge and falling edge spinup interrupts are set simultaneouly.(DCSG01373049)
-[9500 PL] Add addition debug data on detecting Link Hang interrupt.(DCSG01376930)
-Increased SATA Initialization timeout and made it configurable by NVDATA.(DCSG01383806)
-PL: Add NVDATA switch to apply new NVMe Clock out setting for MegaRaid 9560 controllers.(DCSG01383812)
-IT Firmware: Increase number of "AllowedFunction" entries in IOUnitPage13 from 20 to a.(DCSG01388196)


Version 23.125.17.00
---------------
    BIOS            Firmware      UEFI Driver   
  9.45.01.00      23.00.01.00     23.00.01.00

One thing I would like to point that these FW pkg has the SAME FW version
so there will not be any change list.
440-FW          
23.125.13.00-DCSG01229202 (FW:23.00.01.00)            
23.125.16.00- DCSG01368804(FW:23.00.01.00)              
23.125.17.00-DCSG01474661(FW:23.00.01.00)

Version 23.125.16.00
---------------
   BIOS            Firmware      UEFI Driver   
  9.45.00.00      23.00.01.00     23.00.00.00

Fw don't have any change,so don't have any fixed issue.

Version 23.125.13.00
---------------
    BIOS            Firmware      UEFI Driver   
  9.45.00.00      23.00.01.00     23.00.00.00

Defects:
-IOC Page 7 does not report the updated "SASNotifyPrimitiveMasks".(DCSG01220829)
-Wrong link speed check while setting host port status gpio.(DCSG01221053)
-HW Workaround:Link between Controller and expander not always recovering after link reset.(DCSG01196230)
-Disable SATA protocol when in optical mode.(DCSG01194126)
-Updated GoldenX to handle the CoreDump Region.(DCSG00042890)

Enhancements:
-[9500] Add support for host phys/lanes in Port Status Green GPIO.(DCSG01207029)


Version 20.125.03.00
---------------
    BIOS            Firmware      UEFI Driver   
  9.39.00.00      20.00.04.00     20.00.01.00

Defects:	
 Imbalanced bandwidth performance with 2 x4 expanders connect to Aero IT controller(DCSG00950631
 Blue Screens while collecting "pl dbg" logs(DCSG00984451
 UBM statistics data collection and UBM error handling fixes(DCSG00975065
 Fault 0x070A observed while performing firmware downgrade.(DCSG00758163
 Ventura/Mercator: pl: 4311 fault(DCSG00918020
 Two elements of SES Page A are assigned same slot number for UBM backplanes with x2 DFC(DCSG00966202
 Hot add drive on UBM backplane with x2 or X4 DFC reports incorrect element status in SES Page 02h(DCSG00967012
 Response to OOB command is not sent on Internal Dynamic Memory Allocation failure(DCSG00906577
 BST: invalid syntax for Uart config(DCSG00957157
 [Aero][UBM] Enhance the link configuration to handle the link speeds for SAS/SATA drives behind UBM.(DCSG00552897
 Update SSUTimeout Fields Value in BIOS Page 1 to 0xF0(DCSG00982364
 Critical Error Log created if the Firmware Download of BIOS using BIOS image from different package than Firmware.(DCSG00951807
 Fault 0x7600 observed when 1 phy is disabled in SAS IO Unit page 1(DCSG00788430
 Drives not discovered when an enclosure is hot plugged after removing a PCIe switch based JBOF(DCSG00957168
 Unsupported MPI Config page read from OOB provides data in response(DCSG00937617
 SPDM lib compile error for Ventura build(DCSG00810786
 SPDM key reading failed when complete flash Erase case(DCSG01032600
 Coverity : Remove dead code(DCSG00982343
 VSES : Multiple elements of SES page 0xA are assigned the same slot number(DCSG00973316
 pl: NVMe: Format Unit FMTDATA bit should be ignored(DCSG00063448
 PL NVMe : IOs fail with SGL length shorter than the transfer legth(DCSG00501518
 Performance drop seen with direct attached SAS/SATA drives(DCSG00980873
 [BST] Topology information parsing using FW Diag commands is failing(DCSG01045324
 pl: backend PCIe: PCIe error handler fails to issue task management with cascading errors(DCSG00839445
 FW BST: Larger size IO jobs take more time to start, triggering timeout exception in SAL(DCSG00961165
 BST: Fix scripts for SAL stability.(DCSG01012237
 Performance drop seen with SAS/SATA drives in Windows using latest driver(DCSG00981706
 Update Version Field value in Std Inquiry Data of vSES Device(DCSG00966397
 Enclosure handle for some direct attached device might be wrong during Event replay for direct attached slot order case.(DCSG00381441
 Data length from host to DA-SEP device not checked if it is more than buffer length in firmware(DCSG00915992
 [BST] SEP locate test fails on Atlas attached NVMe drives(DCSG01039953
 [Aero][PLDM] PLDM Timer restart failing(DCSG00430198 (Port Of Defect DCSG00830822)
 Controller Faults when connected to DA SEP Backplane(DCSG00916381 (Port Of Defect DCSG00918045)
 [Aero] Phase 18 build error fix(DCSG00708175 (Port Of Defect DCSG00708188)
 Bad PHY events generated by RAID stack for invalid VSES elements slot with Critical status(DCSG00925970 (Port Of Defect DCSG00927932)
 FW Fault 2622 observed during system boot up in some new Gen4/Gen5 servers(DCSG00947451 (Port Of Defect DCSG01019237)
 HBA hangs on boot with failed UBM backplane in a multi-UBM backplane topology(DCSG00653774 (Port Of Defect DCSG00707457)
 Fixed fault 0xF000 when doing VSES task management(DCSG00927996 (Port Of Defect DCSG00934187)
 Some drives missing in OS when Direct attached slot order event replay flag is set in NVDATA(DCSG00991409 (Port Of Defect DCSG00996086)
 Some drives and enclosures not added to Windows OS when SAS/SATA devices are reduced in NVDATA.(DCSG00654062 (Port Of Defect DCSG00757561)
 Fault 0xEE19 observed while running lane break test with managed switch attached to controller.(DCSG00939163 (Port Of Defect DCSG00947866)
 (SATA Only) IO Timeouts seen while running Unmap, SATA Passthrough and Read/Write IOs to a SATA drive(DCSG00654439 (Port Of Defect DCSG00831920)
 MCTP : MCTP MPI requests are failed with drive missing status even when drive is present(DCSG00952803 (Port Of Defect DCSG00956655)
 [Aero][OOB] Firmware download in loop from OOB in PCIe mode fails(DCSG00555977 (Port Of Defect DCSG00831123)
 SATA : one or more HDD are not discovered by OS when drives behind expander are powered ON(DCSG00947126 (Port Of Defect DCSG00964427)
 pl: SAS IO Unit Page 1 Write Current may not cause phy to be enabled(DCSG00654031 (Port Of Defect DCSG00734511)
	
EnhancementRequest:	
 BST: Bring up new Aero activity BST server at BLR(DCSG00323525
 BST: Update boardnames in configuration data(DCSG01010542
 Connector Order change for 9502-16e controller(DCSG00966344
 Create Partial XML for 9502-16e HBA(DCSG00930106
 MPI 2.6: Header file changes associated with revision 2.6.11(DCSG00293141
 pl: backend PCIe: target link speed diag command(DCSG00757333
 Add support for FW UART console to BST scripts(DCSG00776933
 Code Coverage improvement for managed switch SES stack(DCSG00949284
 SNTL Code coverage Improvement(DCSG00949306
 BST: Add custom Cardnames to BST UART configuration(DCSG00985842
 Code Coverage improvement for managed switch MPI device stack(DCSG00949285
 Release Automation: Check for failure during baseline creation(DCSG00958012
 [BST] Graceful handling of controller reset scenario(DCSG01027037
 SAS phy port configuration of UBM connected phys based on UBM DFC Link width.(DCSG00927212
 [OEM][BST] Add a new OEM server to BST(DCSG00776916
 PL SATL : Add SAT translation for the Concurrent Positioning Ranges VPD page(DCSG00927210
 PL SATL : Update the WRITE SAME command to account for Zoned Block Devices(DCSG00500552
 Remove SASPARSER binary from Release Order(DCSG00957868
 Release Automation: automate rebase operation for phase specific streams(DCSG00950531
 UBM error handling improvements and debug statistics data collection(DCSG00903198
 Add cable breaker support to BLR test Hosts(DCSG00777063
 BST: Replace Python's telnet lib APIs with invocations of native telnet client(DCSG01008755
 Integrate MPI 2.6.11 headers(DCSG00408836
 cable breaker exception handling and support for array controller(DCSG00086796
 SATL : ATA Passthruough command handling when Datalength in MPI < data requested to drive(DCSG00833193
 BST: Update Enclosure Logical ID for BST setups(DCSG01015576
 [BST] Add SEP related test cases(DCSG00949307
 [Aero][BST] Improve the code coverage of file plPciDeviceManager.c(DCSG00947724
 Update SAS 3.5 FW summary release notes(DCSG00979878
 [Aero][BST] Improve the code coverage by adding new test cases(DCSG00948894
 CFGI: Integrate MPI 2.6.11 headers with CFGI Lib.(DCSG00481628
 Update 9500-16i, 8i channel XMLs to support new VPP backplane management device address.(DCSG00351950
 BST: Add locate PD test cases to UBM BST(DCSG00019759
 PL SATA : Read logpage 12 and 13 during SATA initialization to get features supported for NCQ encapsulation using FIS porting(DCSG00779724
 PL : Remove obsolete workarounds(DCSG00008204
 BST: On IO errors, retry IO after some delay(DCSG01029567
 Enable collection of PCIe Link event "RECEIVED_NAK_DLLP" (EventCode=0x08) by default(DCSG00122084
 SPDM feature compile out from FW code(DCSG00707071
 [Aero] Enable UBM detection logic on all connectors for OEM HBA with SEP_PRESENT GPIOs(DCSG00927207
 Release Automation: Assign release type when creating ROP(DCSG00941419
 Support streaming of debug logs (HTB) via I2C OOB band on Ventura/Aero IOC/HBA (Part B)(DCSG00927213
 [BST]Add support to execute scripts for one specific card(DCSG00961877
 [UBM] Add detection of SAS/SATA drive with UBM backplane supporting IFDET2# and PRSNT#(DCSG00945423
 Blackduck: Remove non UTF-8 encoding characters from source files(DCSG00258258
 Add 9502-16e board Nvdata to Aero ROP(DCSG00966467
 Code Coverage improvement for NVMe SGL analysis and translation stack(DCSG00949287
 Support downloading of the Host-based Trace Buffer (HTB) via MCTP OOB Interface on Ventura/Aero IOC/HBA (Part A)(DCSG00500554
 BST: When comparing slot numbers, ignore the strings from eminfo command output(DCSG01007045
 BST CodeCoverage : Add BST test case to improve MPI task management code coverage(DCSG00999219
 [Aero][PLDM] Platform changes to accommodate latest PLDM baseline(DCSG00447989 (Port Of EnhancementRequest DCSG00500775)
 SEKM Support for IT controllers(DCSG00433132 (Port Of EnhancementRequest DCSG00777312)
 SEKM: Prevent firmware Download of firmware that do not support SEKM when SEKM is enabled.(DCSG00549524 (Port Of EnhancementRequest DCSG00816022)
 Error handling of UBM CHANGE_DETECT# signal(DCSG00962565 (Port Of EnhancementRequest DCSG00963253)
 [SPDM] Blocking slots 1-7 from configuring SPDM certificates(DCSG00500296 (Port Of EnhancementRequest DCSG00507210)
 Reintroduces the previous security page as MR_MPI26_CONFIG_PAGE_SECURITY_1 to align with current NVDATA(DCSG00977495 (Port Of EnhancementRequest DCSG00977500)
 SEKM feature enhancements to handle error scenarios(DCSG00777328 (Port Of EnhancementRequest DCSG00903186)
 Enhance Error scenario handling in SEKM Feature code(DCSG00966411 (Port Of EnhancementRequest DCSG00974796)


Version 18.125.06.00
---------------
    BIOS            Firmware      UEFI Driver   
  9.35.00.00     18.00.03.00     18.09.01.00

Fix issue:
-Disk cannot be detected after the driver of CFF 440-16i is loaded during installation Windows 2022

Version 18.125.04.00
---------------
    BIOS            Firmware      UEFI Driver   
  9.35.00.00     18.00.02.00     18.09.01.00

Fix issue:
System hung at DXE INIT side

Version 18.125.03.00
---------------
    BIOS            Firmware      UEFI Driver   
  9.35.00.00     18.00.02.00     18.09.01.00
Ph_18

Defects:
-PL SATA Only : SATA PFA drive is not recognized as PFA drive in Aero while hot-plugging.(DCSG00427743
-Some drives and enclosures not added to Windows OS when SAS/SATA devices are reduced in NVDATA..(DCSG00654062
-Ring buffer decoder GUI hangs if timestamp is invalid.(DCSG00437238
-[NVMe] Firmware download in mode E failed with error Invalid Firmware Image.(DCSG00313245
-[Code Review] Updated CoreDump related data structures to have capitalized first letter for the member fields.(DCSG00250948
-pl: NVMe: chain to PRP SGL for non-read/write IO may be handled improperly.(DCSG00408313
-[NVMe] Send diagnostic to abort background test completes with success when no background test started..(DCSG00310330
-[NVMe] Inquiry command to NVMe device reporting old rev firmware after drive firmware update completed successfully.(DCSG00321504
-SPDM IT:SPDM BMC bring up on P2 server.(DCSG00238540
-SPI LIB 1 - Manual Flash writes to flash parts connected to chip selects other than 0 fail..(DCSG00350016
-Aero: PL with newer Atlas FW (4.2) has extra slot number in the Atlas enclosure.(DCSG00284238
-Format Repair operation fails on certain NVMe drive.(DCSG00408635
-Ventura/Mercator: pl: direct attached SAS or SATA device may not be discovered.(DCSG00408109
-SPILIB: NVSRAM uses old ASENB command.(DCSG00342936
-[NVMe] Protect bit is always set in standard inquiry data for NVMe drives..(DCSG00301661
-README file mentions sas2parser instead of sasparser.(DCSG00394150
-PL SNTL : Accumulated Power On Hours value reported by LogSense translation is byteswapped.(DCSG00499729
-[NVMe] SCSI TUR command fails when sent to a NVMe drive with corrupted LBA 0.(DCSG00299624
-[Ventura] Some NVMe drives are not discovered.(DCSG00301612
-SPILIB: FIx definition of SPI_LIB_TYPE for SPILIB1.(DCSG00354885
-SPILIB2: Some properties functions access the wrong array.(DCSG00340954
-[NVMe] Send diagnostic with self test bit 1 but selftestcode non 0 is not failed..(DCSG00306498
-Move Version control files to folder for Release BST.(DCSG00342866
-[NVMe] Mode Select command to write Read Write Error recovery page fails..(DCSG00307175
-[VSes] Connector name of the VSes device in SAS device page 0 has invalid data if no device is connected to port 0.(DCSG00383998
-[Aero] Phase 18 build error fix.(DCSG00708175
-BST: ScrutinyCli invoked with invalid options.(DCSG00428615
-Fixed PH17 Coverity issues.(DCSG00335212
-[NVMe] PL Fault 0xE429 is seen while performing reset for certain NVMe drive..(DCSG00395750
-pl: NVMe: status code type not checked upon Write Buffer callback.(DCSG00419779
-Coverity found defects for converting an expression to a narrower type in SATL code..(DCSG00297461
-[Ventura][NVMe] Phy disable from application does not removed the drive from PL..(DCSG00384856
-PL fault: Invalid Msg Frame fault triggered on external card connected to UBM BP.(DCSG00408493
-Uninitialized pointer access in UBM code..(DCSG00446918
-[VSes] SCSI State not correctly set for some error response to SCSI commands..(DCSG00312554
-[NVMe] Extended Self Test Completion time in Control mode page is byte swapped.(DCSG00308453
-Trigger script with PassComponentTable Command set to invalid Value led to rolling PLDM error messages.(DCSG00500454
-pl: NVMe: async event handler proceeds during IO quiescing.(DCSG00431716
-Fix coverity reported defects.(DCSG00282926
-[NVMe] Parameter Code in Self Test Results log page is incorrect..(DCSG00422250
-Element Status code of a Slot in SGPIO BP with no drive marked as 'Unknown'.(DCSG00428815
-AXI access errors causing FW asserts or faults due to invalid SATA passthrough commands.(DCSG00215338
-pl: SAS IO Unit Page 1 Write Current may not cause phy to be enabled.(DCSG00654031
-[NVMe] TSD bit not getting set in Reference Temperature log parameter.(DCSG00430063
-MBEDTLSLIB: Compile out Mbed TLS Self-Test code.(DCSG00335755
-Update SBLIB version in BST version file.(DCSG00316342
-Update the Driver Trigger Page data structs' size and add padding to make them 256 bytes.(DCSG00258095
-Performance drop of 5-9% seen with Random Read/Write IOs to NVMe drives..(DCSG00258412
-SPILIB2: Small misaligned transfers sometimes result in a read-back verify failure on page writes.(DCSG00283387
-[SPDM IT] Return actual size of certificate chain content to SPDM LIB.(DCSG00233805
-pl: backend PCIe: fix a couple of issues related to PCIe discovery and NVMe init.(DCSG00355408
-NVMe Repair Operation hangs on a certain NVMe drive with Multiple Namespace.(DCSG00415462
-Fix Coverity issues.(DCSG00293500
-Release Automation: If release job web page takes more than 60 secs to load, script throws exception.(DCSG00297363
-MAC verification failed due to inconsistent secure ID.(DCSG00309854
-pl: Incorrect c0 values displayed for SAS/SATA in the "pl serdes tx" output.(DCSG00422289
-NVMe : PROTECT bit in inquiry data is set..(DCSG00308451
-Aero: HW Workaround - When Aero is in the L1 state it periodically (every 2 ms) transitions to L0 and back to L1.(DCSG00501537
-VSES getting removed in OS on controller reset..(DCSG00301631
-[Aero] SAS SATA only partial nvdata xml are not included in release order..(DCSG00394146
-[NVMe] Mode select command to set Control Mode page with last two bytes changed completes successfully..(DCSG00315331
-SPDM Authentication fails when BMC re-triggers SPDM Handshake.(DCSG00547436
-PL Backend PCIe : SATA drive discovery is delayed.(DCSG00310045
-SPDMIT: Return appropriate error to SPDM Lib when read certificate from security page 0 fails.(DCSG00299079
-[NVMe] The long LBA bit is not set in Mode Parameter header..(DCSG00319580
-Coverity issue.(DCSG00293875
-PL Fault 0xEA11 observed, while upgrading Atlas FW using StorCLI in presence of bad NVMe PD's present in the Atlas..(DCSG00324838 (Port Of Defect DCSG00340935)
-[Aero] Controller missing in System Bios..(DCSG00411545 (Port Of Defect DCSG00420098)
-SATA Only: Command timeout observerd on SATA drives.(DCSG00344039 (Port Of Defect DCSG00356008)
-Ventura/Mercator: pl: 4311 fault.(DCSG00918020 (Port Of Defect DCSG00929451)
-Out of bound memory access when assigning dma group for controller devices..(DCSG00243152 (Port Of Defect DCSG00243641)
-Observed PL Fault 6231 while running IOs along with Expander phy link reset..(DCSG00363807 (Port Of Defect DCSG00373461)
-Device add/remove event sent with wrong enclosure handle in certain multi VSes topology..(DCSG00350248 (Port Of Defect DCSG00380548)
-EID is not assigning back with IT controller restart.(DCSG00394045 (Port Of Defect DCSG00397565)
-PL NVMe : PCI task management is not getting completed..(DCSG00231422 (Port Of Defect DCSG00266053)
-During OS reboot some drives go missing..(DCSG00354770 (Port Of Defect DCSG00361759)
-System bios hangs during initial drive discovery..(DCSG00312551 (Port Of Defect DCSG00382416)
-HII Refresh Topology Hangs when connected to Faulty SES Device.(DCSG00385938 (Port Of Defect DCSG00404446)
-Enclosure ID of some Switch attached NVMe devices missing after system reboot..(DCSG00414735 (Port Of Defect DCSG00426692)
-(SATA Only) IO Timeouts seen while running Unmap, SATA Passthrough and Read/Write IOs to a SATA drive.(DCSG00654439 (Port Of Defect DCSG00906897)
-[SATA Only] SCSI Start Stop Unit command with power condition active fails..(DCSG00349970 (Port Of Defect DCSG00353138)
-0x6001 Fault running TMs with certain NVMe translated Host IOs.(DCSG00362831 (Port Of Defect DCSG00385767)
-Drives connected behind external card with VSES disabled, failed to detect in Linux OS.(DCSG00350402 (Port Of Defect DCSG00363785)
-Firmware fails to send Enclosure removal event to host when the enclosure is removed from the topology..(DCSG00232962 (Port Of Defect DCSG00244617)
-[Aero/Ventura] Bootloader corruption with firmware download and DC cycle in loop..(DCSG00238233 (Port Of Defect DCSG00245454)
-ParentDevHandle value calculated for given Phy Number is incorrect for Direct Attached Devices in Event Replay logic.(DCSG00299632 (Port Of Defect DCSG00299823)
-Controller Faults when connected to DA SEP Backplane.(DCSG00916381 (Port Of Defect DCSG00918083)
-[SATA ATAPI] FW fault 0x6231 seen while completing some IO for ATAPI device..(DCSG00350047 (Port Of Defect DCSG00353918)
-[Aero][UBM] Enhance the link configuration to handle the link speeds for SAS/SATA drives behind UBM..(DCSG00552897 (Port Of Defect DCSG00706402)
-PL : Missing drives during AC power cycle test.(DCSG00275868 (Port Of Defect DCSG00301823)
-ExtManPage41 TX Values are not being applied / run by AERO SERDES.(DCSG00311524 (Port Of Defect DCSG00311739)
-0x6001 Fault while running driver load/unload with simultaneous NVMe drive pulls.(DCSG00378243 (Port Of Defect DCSG00385686)
-PL: 9460-16i incorrect slot numbers assigned attaching to OEM specific mixed mode backplane.(DCSG00243953 (Port Of Defect DCSG00342787)
-[Aero][PLDM] PLDM FW discovery results in 265D Fault.(DCSG00307769 (Port Of Defect DCSG00330183)
-Ventura: Faults 0x0101 and 0x5805 Invalid LMID Index Seen after hundreds of cold boots.(DCSG00338118 (Port Of Defect DCSG00384000)
-Serdes TX table in pl diag dump has the Pre-cursor, Post-cursor and Attenuation values mixed.(DCSG00388268 (Port Of Defect DCSG00404448)
-NVMe Init error drives are not discovered after pull/push within DMD timeout.(DCSG00242197 (Port Of Defect DCSG00250023)
-ventura build issue with PL PCI DEVICE feature disabled.(DCSG00286358 (Port Of Defect DCSG00286361)
-SATA only: WRITE SAME NCQ encapsulation assumes NonData NCQ is supported if Zero EXT is Supported.(DCSG00398894 (Port Of Defect DCSG00412030)
-Update the SPDM print index properly before adding the prints to ring buffer.(DCSG00335886 (Port Of Defect DCSG00337717)
-[NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive.(DCSG00136092 (Port Of Defect DCSG00237479)
-LED Blink/Unblink operation fails on certain Slots in UBM using MPI SEP Request.(DCSG00282826 (Port Of Defect DCSG00290200)
-PL NVMe : PCI task management is not getting completed..(DCSG00231422 (Port Of Defect DCSG00245537)
-[Aero][OOB] Firmware download in loop from OOB in PCIe mode fails.(DCSG00555977 (Port Of Defect DCSG00908352)
-Ventura: SAS3616W or SAS3616W based boards have links less than epected width.(DCSG00249594 (Port Of Defect DCSG00249753)
-[Aero][PLDM] PLDM Timer restart failing.(DCSG00430198 (Port Of Defect DCSG00960384)
-Remove LogSpecific member in the structure 'IOPI_LOG_DETAIL.(DCSG00318366 (Port Of Defect DCSG00318943)
-PL SATA Only : Controller hang observed for ATA Passthrough command with count value set to 0.(DCSG00250952 (Port Of Defect DCSG00266833)
-PL fault 0xE40E observed accessing unconfigured MPI backend device registers through CLI cmd.(DCSG00234837 (Port Of Defect DCSG00238649)
-9500-16e disappears on system reboot.(DCSG00367091 (Port Of Defect DCSG00414022)
-HBA hangs on boot with failed UBM backplane in a multi-UBM backplane topology.(DCSG00653774 (Port Of Defect DCSG00707464)
-OEM UBM backplane Slot status LED Blinks only for 10 secs for NVMe VDs with Toggle Host LED management.(DCSG00323361 (Port Of Defect DCSG00380726)
-Controller fault observed on changing some phys to manual port config with port set to 0..(DCSG00237498 (Port Of Defect DCSG00245531)
-Aero A0: Controller faults 0xD015 with Refresh topology from BIOS in a managed PCIe switch config..(DCSG00414714 (Port Of Defect DCSG00418238)
-[Aero][PLDM] Date format exposed by IT to PLDM library is not as per PLDM spec.(DCSG00363642 (Port Of Defect DCSG00398739)
-9500-16e fails to recover after warm boot.(DCSG00422618 (Port Of Defect DCSG00422813)
-PL: Reply to IO's bad SGL to Atlas SES has wrong DevH and SMID's incorrectly tries to fit 3 SGEs inframe.(DCSG00315476 (Port Of Defect DCSG00366033)
-[VSes] Element status set to 'Unknown' in SES page 2 of VSES for some phys where nothing is connected..(DCSG00333163 (Port Of Defect DCSG00343848)
-Make Clear of the PEPP version of ConfigValid Applicable to IT Boot Code Only.(DCSG00398453 (Port Of Defect DCSG00404468)
-As part of the Device Add\Removal Event, the enclosure handle passed on by the PL FW to the upper layer is incorrect..(DCSG00298128 (Port Of Defect DCSG00299826)
-When performed export csr for all 8 slots in batch observing for few slot command is success and for other it is failure..(DCSG00421812 (Port Of Defect DCSG00425171)
-NVMe Init Error: Device with no namespaces shows 'Namespace count Invalid' as Unrecoverable Error.(DCSG00290593 (Port Of Defect DCSG00303510)
-pl: backend PCIe: limit CRS retry count.(DCSG00312206 (Port Of Defect DCSG00324774)
-[VSes] Slot status is reported as 'Unsupported' for drives connected to UBM backplane..(DCSG00337912 (Port Of Defect DCSG00353069)
-PL NVMe : IOs fail with SGL length shorter than the transfer legth.(DCSG00501518 (Port Of Defect DCSG00735325)

EnhancementRequest:
-SPILIB2: Add support for AV1 ring buffers	EnhancementRequest ID: DCSG00421632
-OEM Smart Carrier Backplane code cleanup	EnhancementRequest ID: DCSG00171467
-Add new field DEPOPULATION TIME as part of translation of VPD Page - Block Device Characteristics.	EnhancementRequest ID: DCSG00167925
-SPILIB1: CLear LC bits in Spansion, wait longer for NVSRAM	EnhancementRequest ID: DCSG00427348
-SPDM IT: Add memory allocation/free for SPDM_LIB	EnhancementRequest ID: DCSG00229260
-SPILIB2: Integrate 20.00.11.00 with the IT firmware tip	EnhancementRequest ID: DCSG00297796
-pl: backend PCIe: runtime control for lane margining debug console prints	EnhancementRequest ID: DCSG00373313
-SPILIB2: Add spi2FlashWriteDataNoVerify() API	EnhancementRequest ID: DCSG00394830
-pl: NVMe: update to latest SNTL specification Phase 2	EnhancementRequest ID: DCSG00340625
-[NVMe] SCSI Send Diagnostic command translation for NVMe.	EnhancementRequest ID: DCSG00261270
-Enhancement to source of randomness for generating key pair	EnhancementRequest ID: DCSG00208477
-MBEDTLS LIB: Add license files to source tree	EnhancementRequest ID: DCSG00813882
-Add dumps to pl dbg	EnhancementRequest ID: DCSG00008206
-pl: backend PCIe: CRS retry limit disable bit	EnhancementRequest ID: DCSG00325823
-Update SAS 3.5 FW summary release notes	EnhancementRequest ID: DCSG00384316
-SPILIB2: Add support for FLASH suspend/resume.	EnhancementRequest ID: DCSG00371513
-VSES: Removed loginfo code when the command is failed with a check-condition	EnhancementRequest ID: DCSG00235941
-SPILIB2: AV2 Core Support [PA 0.2]	EnhancementRequest ID: DCSG00230517
-Update the event logging when the "CoreDump" region is erased from ScrutinyCLI command	EnhancementRequest ID: DCSG00367325
-Summary of changes	EnhancementRequest ID: DCSG00383538
-[IT SPDM] Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust	EnhancementRequest ID: DCSG00218564
-SPILIB: Add support for multiple erase sizes in uniform flash parts	EnhancementRequest ID: DCSG00309579
-[IT SPDM] Implement client APIs for SPDM Get Measurement command.	EnhancementRequest ID: DCSG00256411
-Add version control file to build	EnhancementRequest ID: DCSG00242260
-Ventura/Aero: Request by MegaRAID to output debug data in vtboot.rom for future debug	EnhancementRequest ID: DCSG00420316
-VSES - UBM DFC Array Device Element status read optimizations	EnhancementRequest ID: DCSG00347743
-[NVMe] Provide interface to reset NVMe drive after shutdown.	EnhancementRequest ID: DCSG00109904
-NVMe Sanitize Translation	EnhancementRequest ID: DCSG00266054
-[NVMe] Update SCSI to NVMe translations based on latest SNTL document.	EnhancementRequest ID: DCSG00235935
-SPI LIB 1- Enable Suspend-Resume support for Winbond and ISSI flash parts.	EnhancementRequest ID: DCSG00380266
-Update the IT/PL Firmware Error codes guide	EnhancementRequest ID: DCSG00349980
-Security Key page MPI definitions should more descriptive	EnhancementRequest ID: DCSG00336313
-SPILIB2: Add Avenger2 Duty Cycle and Sample Delay options	EnhancementRequest ID: DCSG00287035
-Enable 24 NVME drive support for internal and external controllers	EnhancementRequest ID: DCSG00306646
-SPILIB: Add 1_4_4 read/write and NVSRAM commands to analyzer decoder	EnhancementRequest ID: DCSG00358690
-SPLIB2: Eliminate debug prints from NVSRAM init	EnhancementRequest ID: DCSG00299483
-SPILIB 2.0 : expander/Atlas Modify time loops to handle multi-processsing better	EnhancementRequest ID: DCSG00220784
-[Ventura/Aero] Block the OOB FW download when firmware update is in progress.	EnhancementRequest ID: DCSG00249958
-SPILIB2: Add support for 100 MHz using default configuration for Macronix 256 MBit	EnhancementRequest ID: DCSG00409337
-Host Trace Buffer Triggers to be persistent	EnhancementRequest ID: DCSG00235945
-Added IOCParam to IOUnit Control command to allow periodic time-sync	EnhancementRequest ID: DCSG00235948
-[SPDM IT] Export CSR & Import Cert Open & Close Session	EnhancementRequest ID: DCSG00221406
-SPILIB2: Add code to clear block protect bits if they are set	EnhancementRequest ID: DCSG00420314
-SPILIB 2.0: Avenger2 and R processor build support	EnhancementRequest ID: DCSG00230514
-Release Automation: Add support for generating Ventura ROP	EnhancementRequest ID: DCSG00246102
-Aero Secure Boot: Add Key Update Pending Check for 'COMPLETE' Image Download	EnhancementRequest ID: DCSG00241566
-[Aero/Ventura]Fix Coverty issues in Phase_18 TIP	EnhancementRequest ID: DCSG00507240
-Support for Mode 5 NVMe drive firmware download with Chain SGL SCSI Write buffer request.	EnhancementRequest ID: DCSG00171452
-Total vSES Enclosure Slot Count value reported is incorrect in host tools\MR FW with NVMe drive which fails initialization	EnhancementRequest ID: DCSG00546745
-[NVMe] Prevent non Read/Write SCSI IO Timeouts while running heavy greater than MDTS RW IOs	EnhancementRequest ID: DCSG00234748
-NVMe Init Failure Reporting & Recovery of NVMe Drive with Partial Capacity NSID 1 Namespace	EnhancementRequest ID: DCSG00310384
-SPDMLIB: Support SPDM Challenge command request for hash of all supported measurements	EnhancementRequest ID: DCSG00366048
-Vent/Aero: Integrate SPILIB 20.00.14.00	EnhancementRequest ID: DCSG00317165
-Log 0 SPDM events for certificate slot & key management	EnhancementRequest ID: DCSG00322202 (Port Of EnhancementRequest DCSG00366811)
-[Aero][PLDM] Platform changes to accommodate latest PLDM baseline	EnhancementRequest ID: DCSG00447989 (Port Of EnhancementRequest DCSG00960360)
-VSES: Update diag page 02h status reporting for Array device elements to use UBM DFC SnC Desc Element status code	EnhancementRequest ID: DCSG00308393 (Port Of EnhancementRequest DCSG00379789)
-[SPDM] Blocking slots 1-7 from configuring SPDM certificates	EnhancementRequest ID: DCSG00500296 (Port Of EnhancementRequest DCSG00645950)


Version 16.125.15.00
---------------
BIOS            Firmware      UEFI Driver   
9.31.00.00     16.00.12.00    16.00.08.00
Ph_16.0

Defects:
-PLDM single firmware update logs multiple debug messages in controller trace buffer.(PLDM single firmware update logs multiple debug messages in controller trace buffer)
-PLDM Type 2 - Change debug print filter level to "Warning" for PollForPlatformEventMessage command.(DCSG00263767)
-Fix Coverity tool reported defects.(DCSG00266270)
-fixed the parameter difference for the PLDM Type 5 print framework..(DCSG00286651)
-pldmFreeFwUpdtResources() doesn't frees RetryRqstTimer correctly.(DCSG00313887)
-Issue in freeing PLDM firmware update resources.(DCSG00317911)
-Assertion failure in fw\cpu\arm\exceptions.c at line 1006 on triggering QueryDeviceIdentifier command in Download State.(DCSG00337907)
-Coverity defects fix..(DCSG00340836)
-PLDM Type 2 - Fail module initialization if Managed Device invokes initialization API without allocating memory.(DCSG00360498)
-OOB-MCTP over I2C - FW updates in Loop hits PLDM Fault 0x6.(DCSG00380088)
-PLDM - Fix compilation errors reported in an OEM platform.(DCSG00382501)
-Doxygen build error.(DCSG00415793)
-[Aero][PLDM] PLDM Timer restart failing.(DCSG00430198)
-Updated GoldenX to handle the CoreDump Region.(DCSG00042890)

Enhancements:
-Implemented linked list for entity and sensors.(DCSG00219964)
-Add snapdump support for PLDM Type 2 and Type 6 modules.(DCSG00226303)
-PLDM Type 2: Implement API changes and support for Redfish message event in PLDM Monitoring and Control module.(DCSG00253011)
-PLDM Type 6 - Add support for Redfish Message Event.(DCSG00255563)
-PLDM Monitoring and Control: Addressed the Coverity reported issues and added abort function.(DCSG00342504)
-Address Coverity tool reported issues in PLDM Type 2 and Type 6 modules.(DCSG00352028)
-Enhance PLDM library for separation of APIs/LIB and source code.(DCSG00394996)
-Code cleanup activity.(DCSG00395207)
-PLDM - Handle a TODO related to sensor re-arm unavailable in present state and update copyright year in all Type 2 files.(DCSG00404477)
-[Aero][PLDM] Platform changes to accommodate latest PLDM baseline.(DCSG00447989)
-For report LUN command, Increase retry count from 3 to 5 and add SCSI status BUSY into retry loop.(DCSG00930134)


Version 16.125.12.00
---------------
    BIOS            Firmware      UEFI Driver   
  9.31.00.00      16.00.12.00    16.00.06.00
Ph_16.0

Defects:
 -Response of TransferComplete (0x16) become irrelevant if it is received after the successful completion of CancelUpdateComponent(0x1C)and needs to be dropped.(CSG00033524)
 -SPDMLIB: Add change to SConstruct to copy library output file (*.a) to release folder(CSG00117832)
 -CFGI : The first 32 characters of MPI defines should be unique(CSG00086291)
 -SPDM_LIB: Add alignment parameter into SPDMLib_Calloc interface(CSG00237674)
 -PLDM Type 6: Incorrect error code returned for resource unregistration(CSG00067924)
 -NVMe Init reports wrong failure error codes(CSG00103993)
 -Coverity Bugs in PL Enclosure Management Files(CSG00043514)
 -PL: MS-SES with no Array Devices in Atlas SES causes 0x7200 fault(CSG00077263)
 -Additional Key Data field of Security Page 1 is missed in XSD definition(CSG00077979)
 -BST: BST cancellations on cable breaker comm port unavailability(CSG00212793)
 -Unitialized pointer was being accessed(CSG00096545)
 -MBEDTLS LIB: fix compilation error during IT FW build(CSG00234920)
 -SPDM LIB: Set ECDSA signature with correct size in Signature field of SPDM Challenge response buffer before sending to BMC server(CSG00225192)
 -PLDM Type6 : Change filename for fixing doxygen compilation(CSG00081863)
 -PLDM Type5 : Controller FW Downgrade through BMC results in controller FW crash(CSG00095783)
 -SPDM: Attestation failed with wrong Nonce values(CSG00126872)
 -CFGI : MPB2 read fails with invalid checksum(CSG00098544)
 -PLDM: Pass Timer-id that needs to be restarted to Pldm-timer-restart operation.(CSG00018645)
 -Change file name of SpdmDebug.h to SpdmDebugs.h . And Check in SpdmDebugs.h for IT(CSG00074556)
 -PL: Aero -- Atlas US Cable Pull/Push Results in Missing Enclosure Slot Info(CSG00181448)
 -Coverity found defect in MPI Device and FPE modules.(CSG00098787)
 -NVME Drives not getting discovered on inserting in Customer UBM3 x4 backplanes until OCR.(CSG00081732)
 -[Aero][PLDM] Date format exposed by IT to PLDM library is not as per PLDM spec(CSG00363642)
 -BST: version.mak no longer a part of BST verification(CSG00368158)
 -Correct Sblib Int make sure ER 110403 and ER 166877 are present (2)(CSG00215388)
 -BST: UBM BST funtonality is broken on latest BST code.(CSG00216461)
 -Observed Data Corruption during IO stress test.(CSG00212797)
 -PLDM Type-2 : GetPDRRepository command fails with large configuration (mulitple drives and volumes)(CSG00097462)
 -Addressing IT raise defects in SPDM library change.(CSG00061718)
 -MBEDTLS LIB: Fix dynamic memory release bug in Mbed Tls Library(CSG00216944)
 -Aero A0: Fault D033 running IO + Expander Phy Link/Hard Resets to Expander phys(CSG00045450)
 -BST: Case mismatch in card name(CSG00114314)
 -Phase 15 Coverity Bug Fixes(CSG00104982)
 -Large topology of more than 500 drives cannot be supported on SAS 3.5 Channel Controllers(CSG00108246)
 -Mismatch between subsystem id in NVDATA and SBR for 9405-W 16i(CSG00077700)
 -BST: Num Slots config file update for topology with Atlas Configuration(CSG00312633)
 -Release Automation: Exceptions during execution of release script(CSG00151389)
 -Aero A0: External cards do not support more than one PCIe drives.(CSG00249770)
 -Do not process any response msg if FD is in PLDM_FW_UPDT_IDLE state.(CSG00024158)
 -[SPDM] SPDM lib changed one of header file name , seeing compilation error in IT.(CSG00077919)
 -IT SPDM commands not working via host interface(CSG00134673)
 -PCIe Switch Page 250 has NumPorts set to zero, and this page is not included in "iop show cfg all"(CSG00101756)
 -MBEDTLS LIB: Add change to SConstruct to copy library output file (*.a) to release folder(CSG00117834)
 -Coverity Defects in SATA and VPP code.(CSG00234415)
 -MFG Page 49/50/51 defines are not compiled(CSG00083748)
 -MBEDTLS Lib: Alignment issues while certificate verification on IT cards(CSG00312818)
 -Aero: PswSbr.bin file is read only and causes an error when running the RMC script(CSG00082963)
 -SPDM_LIB: Set tagOwner as per SPDM request.(CSG00239464)
 -BST: Fix the compilation error for UBM BST(CSG00062522)
 -PL: SMP Timeouts During Expander Phy Reset Test(CSG00043616)
 -[Aero] SATA drive gets dropped when corresponding phy is disabled and enabled.(CSG00222544)
 -PL: Adjust the MPI Device support check to only support Atlas's MPI Device(CSG00040939)
 -Updating FW (on 9400 series HBA) from Ph-7 to Ph-14 causes "invalid flash" message on FW bootup(CSG00167100)
 -Fail to read Extended Expander Page 250(CSG00092804)
 -BST: SAL reports unknown device type for drives(CSG00239268)
 -pl: NVMe: 265D fault in out of resource case(CSG00093410)
 -Phase 15 Coverity Bug Fixes(CSG00105045)
 -[BST] Remove the erase persistent test case from BST.(CSG00305439)
 -(MS SES) Non data transfer SCSI IO failed with Invalid SGL error(CSG00234926)
 -Duplicate MPI Toolbox Tool Values in MPI temp(CSG00086898)
 -NVMe device not discovered after disable-enable PCIe link in PCIe IO Unit page 1(CSG00082524)
 -BST: ELID update due to SAS-Address update on Blr Servers(CSG00301666)
 -BST: POR Reboot requires a further check(CSG00086783)
 -Controller fault 0x1902 is seen while issuing locate command to NVMe drives(CSG00062252)
 -PLDM RDE - MultipartReceive command fails with error INVALID_DATA for non-zero OperationID(CSG00165437)
 -Fixing Coverity issues(CSG00096489)
 -SBLIB: Getting Inconsistent secure ID on IT cards(CSG00309847)
 -BST: Aero with Atlas switch Num slot update(CSG00284255)
 -Skip completeflash images during BST(CSG00337918)
 -"Add enclosure event for an enclosure that is already active" error message observed in Windows event logs(CSG00063929)
 -SPDM LIB: Need to include header file SpdmLibTypes.h in SpdmLibIFace.h(CSG00074328)
 -Build error in PLDM Library on ARM 4.1 compiler (done with Atlas FW code)(CSG00019014)
 -PLDM Lib: Unable to stop timer (PLDM Fault 0x11)(CSG00134602)
 -iop show cfgspace doesn't work(CSG00066110)
 -During OS reboot some drives go missing.(CSG00354770)
 -Remove LogSpecific member in the structure 'IOPI_LOG_DETAIL(CSG00318366)
 -PLDM Type5 : Upgrade to the latest signed FW fails(CSG00076949)
 -Bug Fix In get CERT and While reading the certificate from the client(CSG00047643)
 -ED91 Fault while running IOs + OCR (controller reset) testing(CSG00057254)
 -Coverity Defects(CSG00094727)
 -The first 32 characters of MPI defines should be unique(CSG00086266)
 -PH15 Scrutiny CLI: device c command output is not giving the details of the all the devices connected to the expander(CSG00102332)
 -print correct variable during error condition(CSG00096538)
 -pl: backend PCIe: prevent switch rediscovery quirks(CSG00018730)
 -Incorrect slot count is present in config, for a BP connected to external card in BST server.(CSG00319578)
 -Firmware fails to send Enclosure removal event to host when the enclosure is removed from the topology.(CSG00232962)
 -EID is not assigning back with IT controller restart(CSG00394045)
 -Coverity defect fix(CSG00231928)
 -BST: Board naame format error(CSG00143769)
 -[Aero] Application scanning for I2C devices on I2C bus hang when OOB configured to MCTP-PCIe mode(CSG00103208)
 -NVMe Init error drives are not discovered after pull/push within DMD timeout(CSG00242197)
 -9500-16e disappears on system reboot(CSG00367091)
 -PLDM Type 6: BEJ buffer insertion pointer is not incremented when an element is added to array context(CSG00067926)
 -BST: NumSlots fix for Ph14 &15 broke BST on other fw phases(CSG00315471)
 -Sea 16e PCIe TX Compliance Test Failure(CSG00052179)
 -Duplicate slot IDs assigned for SAS/SATA drives on elrond Ex1 backplane when it is connected to 9405W 16i controller.(CSG00072826)
 -Ventura/Mercator: pl: 4311 fault following SAS IO Unit Page 1 write(CSG00099275)
 -PL Backend PCIe: 0xEE1A fault observed with bad clocked Aero and Atlas(CSG00080298)
 -RDE: Valid schema class can't be more than 4 for 'GetSchemaURI' command(CSG00109749)
 -Coverity found defect in SATA and Enclosure management modules.(CSG00098596)
 -Controller fault observed on changing some phys to manual port config with port set to 0.(CSG00237498)
 -Ventura: SAS3616W or SAS3616W based boards have links less than epected width(CSG00249594)
 -Make Challenge Buffer Include Get_Digest/Digest, Get_Cert/Cert(CSG00055393)
 -9500-16e fails to recover after warm boot(CSG00422618)
 -Correct Sblib Int make sure ER 110403 and ER 166877 are present(CSG00214265)
 -BST: Uart Utility re-visit(CSG00113761)
 -pl: backend PCIe: resource leakage during direct attached event generation(CSG00093660)
 -[Aero][PLDM] PLDM FW discovery results in 265D Fault(CSG00307769)
 -Disable CoreDump when Flash device is not present(CSG00054500)
 -BST: Case mismatch for custom card name(CSG00115303)
 -SBLIB: Significantly longer boot times that previously encountered in MR CBB(CSG00299427)
 -Build failed after MbedTLS new base line pulled(CSG00074952)
 -pl: port enable is delayed when SAS/SATA devices are attached to a UBM backplane(CSG00076783)
 -BST: Encl_logical_id update(CSG00298990(
 -Observed PL Fault 0xEE17 when NVME drives connected via PCIe switch.(CSG00108281)
 -[MBEDTLS] Device Key Pair Generation resulting in different Keys on IT card(CSG00318909)
 -Increase the time wait time when quad mode bit gets written for write operation to complete.(CSG00061711)
 -Out of bound memory access when assigning dma group for controller devices.(CSG00243152)
 -SPILIB 2.0: Cypress 256Mbit SPI Flash Is Not Supported(CSG00121768)
 -SPDM_IT_FW:For empty slots IsEmpty field is shown as No it should be shown as Yes .(CSG00230707)
 -Build error in PLDM Library on ARM 4.1 compiler with Atlas FW build environment(CSG00071478)
 -Invalid Completion code Error for running script-LearnComponentStateInvalidTransferFlagPLDMType5.py(CSG00149690)
 -Phase 15 Coverity Bug Fixes(CSG00092935)
 -Some of SAS/SATA drives attached to OEM Aero HBA may not be reported to host(CSG00076717)
 -Connector Name displayed as 'Unknown' in HII for NVMe drives behind Switch(CSG00085845)
 -SPILIB: Winbond 256MBit maximum page write time increased from rev "A" to rev "B" of their specification(CSG00170747)
 -pl: firmware hang occurs in UBM command error case(CSG00072841)
 -Coverity defect fix in FPE code.(CSG00235474)
 -RDE - Controller information is not getting launched in REST client(CSG00099613)
 -Fix SPDM library for Get_Digest, Challenge.(CSG00053409)
 -Update the SPDM print index properly before adding the prints to ring buffer(CSG00335886)
 -Resetting the event counters in Ext. SAS/PCIe IO Unit Page 250 fails(CSG00150901)
 -0x6001 Fault while running IOs and cable pull test(CSG00040422)
 -[SPDM] Fix compilation #include "iopPlatSecCertMgMt.h" case sensitive issue(CSG00109315)
 -SPDMLIB: Reduce number of arguments passed to IT FW debug print functions(CSG00335615)
 -IOP: Trace buffer image has extra "CFG string(CSG00051124)
 -Update NVDATA Major Version on PH16 point release(CSG00309322)
 -(SATA Only) SCSI ATA Passthrough command with set feature command to set the drive in standby_y state sets it to standby_z state.(CSG00080256)
 -Release Automation: Web page button not detected in script.(CSG00137712)
 -pl: NVMe: D062 fault during NVMe init(CSG00083594)
 -PLDM Type 6: Fix "RedACT" tool reported observations(CSG00080427)
 -Check in SpdmDebug.h for IT(CSG00074108)
 -Updated CoreDump specific functions to run from OCM memory and enabled XMEMXOPY(CSG00093703)
 -pl: NVMe: E429 fault on register read failure(CSG00098345)
 -SBLIB: Change bool type to int type in API parameter to maintain compatibility(CSG00100308)
 -PLDM Type 2: Resource associated major schema count is incremented incorrectly(CSG00074150)
 -[PLDM] IT HBA with latest PLDM library faults(CSG00102618)
 -Aero BST: Manage NVMe drive link up timing(CSG00228186)
 -SPDM library to remove %s for any print as IT does not support %s print string.(CSG00061353)
 -Import certificate command with out seal option is failing for slots 0 & 1.(CSG00228127)
 -[Aero/Ventura] MCTP discovery fails after unload and load of MCTP driver in BMC(Board Management controller)(CSG00058897)
 -ventura build issue with PL PCI DEVICE feature disabled(CSG00286358)
 -When performed export csr for all 8 slots in batch observing for few slot command is success and for other it is failure.(CSG00421812)
 -PL: Removal of NVMe Drive that Failed NVMe Init Doesn't Work Correctly(CSG00103998)
 -Aero Seeing "SpdmReadCertForSlot[277]:[Error] Certificate Read Failed" on IT card after Controller Resets(CSG00253315)
 -MAC verification failed due to inconsistent secure ID(CSG00309854 (Port Of Defect DCSG00309857)
 -pl: backend PCIe: 'pl pci devlnk' is missing from the 'pl dbg' dump(CSG00052268 (Port Of Defect DCSG00052348)
 -PL: Initial MPI driver error injection can cause the Managed Switch's SES to not be exposed to OS(CSG00045593(Port Of Defect DCSG00045725))
 -NVMe devices VPD page 83 NAA descriptor may conflict with EUI64 ID reported(CSG00148775 (Port Of Defect DCSG00153702)
 -Remove LogSpecific member in the structure 'IOPI_LOG_DETAIL(CSG00318366 (Port Of Defect DCSG00318944)
 -Ventura; Add code to prevent downgrade from phase 14 to previous phases for winbond(CSG00059594 (Port Of Defect DCSG00061399)
 -Aero: pl: SATA device may not link up following a link down(CSG00054906 (Port Of Defect DCSG00073959)
 -"iop show cfg all" command captured by core-dump is zero(CSG00047928 (Port Of Defect DCSG00050673)
 -PL: Blind retries by MegaRAID FW when PL is in out of resource condition results in IOs to MS-SES exhausting retries(CSG00033753 (Port Of Defect DCSG00046628)
 -pl: backend PCIe: switch rediscovery fails with certain switch configurations(CSG00061635 (Port Of Defect DCSG00062706)
 -PL NVMe : NVMe repair operation fails with metadata(CSG00112303 (Port Of Defect DCSG00121425)
 -VSES SES Page 02h reports Unknown (06h) Element Status for some Array device elements in a wide DFC slot(CSG00069091 (Port Of Defect DCSG00086818)
 -UBM: Incorrect slot number enumerated for a DFC on 3 x4 DFCs UBM config(CSG00048027 (Port Of Defect DCSG00048742)
 -SATA only : Controller hang is observed due to recursive function call.(CSG00139294 (Port Of Defect DCSG00226371)
 -SPDMIT: Return appropriate error to SPDM Lib when read certificate from security page 0 fails(CSG00299079 (Port Of Defect DCSG00306949)
 -pl: NVMe: unexpected NVMe init failure if LBA 0 is inaccessible(CSG00120588(Port Of Defect DCSG00121315)
 -PL NVMe : PCI task management is not getting completed.(CSG00231422 (Port Of Defect DCSG00245538)
 -pl: NVMe: incorrect sense key is returned for Access Denied NVMe status(CSG00063924 (Port Of Defect DCSG00069167)
 -Ventura: The host PCIe link width may be narrower than expected(CSG00078678 (Port Of Defect DCSG00093473)
 -Ventura/Mercator: pl: direct attached SAS or SATA device may not be discovered(CSG00408109 (Port Of Defect DCSG00427398)
 -Some of the drives not listed under Widows OS Disk Management.(CSG00096508 (Port Of Defect DCSG00102661)
 -PL SATA: Sanitize operation is completed before actual completion from drive.(CSG00119155 (Port Of Defect DCSG00126831)
 -pl: NVMe: Select field used during NVMe init without verifying support(CSG00050182 (Port Of Defect DCSG00051206)
 -Incorrect slot mapping on UBM backplane with additional DFCs support(CSG00077969 (Port Of Defect DCSG00082256)
 -LED Blink/Unblink operation fails on certain Slots in UBM using MPI SEP Request(CSG00282826 (Port Of Defect DCSG00299898)
 -Aero A0: External cards do not support PCIe and SRIS by default(CSG00131571 (Port Of Defect DCSG00143420)
 -pl: NVMe: Drive Firmware update fails on mode 0xE(CSG00044028 (Port Of Defect DCSG00052008)
 -Back out changes of ER DCSG00029633 that limits VSES devices to 2(CSG00053379(Port Of Defect DCSG00054368)
 -[SATA Only] SCSI Start Stop Unit command with power condition active fails.(CSG00349970 (Port Of Defect DCSG00405776)
 -Atlas Behind Aero: PL Fault 0xEC1A When Performing Backend PCI Resets From Diagnostic Code(CSG00042688 (Port Of Defect DCSG00147003)
 -BSOD when running CoreDump with Aero connected to Atlas switch(CSG00042497 (Port Of Defect DCSG00044353)
 -Invalidate slot not working for IT SPDM(CSG00131485 (Port Of Defect DCSG00139744)
 -Drive Discovery failed with Port Hot-swap on Aero16e controller(CSG00042446 (Port Of Defect DCSG00052013)
 -Fail to read device and link related counters from Page 250(CSG00080856 (Port Of Defect DCSG00096620)
 -[Aero/Ventura] Bootloader corruption with firmware download and DC cycle in loop.(CSG00238233 (Port Of Defect DCSG00245453)
 -Aero: Firmware Download should return success with loginfo indicating POR is necessary(CSG00055371 (Port Of Defect DCSG00065882)
 -PL: Over 250+ power cycles of managed switch (Atlas) causes an associated SES to be inaccessible(CSG00048699 (Port Of Defect DCSG00059743)
 -ParentDevHandle value calculated for given Phy Number is incorrect for Direct Attached Devices in Event Replay logic(CSG00299632 (Port Of Defect DCSG00299897)
 -[Aero][PLDM] FW version reported wrongly to BMC( Board Management Controller) over out of band(CSG00050201(Port Of Defect DCSG00051130)
 -[Aero/Ventura] Unused phys are managed by VSes in SGPIO BP mode(CSG00151021 (Port Of Defect DCSG00225221)
 -VSES page 02h reports incorrect status for linkup failed array device element on certain UBM slots(CSG00112320 (Port Of Defect DCSG00127720)
 -Ventura B0: Device discovery fails on 9400-16e(CSG00045385 (Port Of Defect DCSG00045779)
 -PL : 0x7008 fault seen when booting the bad clocked controller connected to Atlas(CSG00114774 (Port Of Defect DCSG00121424)
 -Drives connected behind external card with VSES disabled, failed to detect in Linux OS(CSG00350402 (Port Of Defect DCSG00363781)
 -Aero: backend PCIe: link failure after PCIe IO Unit Page 1 link disable(CSG00050164 (Port Of Defect DCSG00051710)
 -Expander attached devices not reported to host if enclosure slot ordering is enabled in event replay.(CSG00108094 (Port Of Defect DCSG00111584)
 -pl: NVMe: EC0E fault after drive pull during NVMe init(CSG00114179 (Port Of Defect DCSG00127917)
 -PL: 2 Atlases in single MPT mode with 2 host ports each will have drives on one switch not mapped to that Atlas's SES Page 0Ah(CSG00054949 (Port Of Defect DCSG00062379)
 -0xD101 Fault observed running non-RW IOs to NVMe devices with drive push-pull(CSG00062701 (Port Of Defect DCSG00071043)
 -PH14 Windows Driver: on 2016,19H2 OS,Getting BSOD for fault command(CSG00048607 (Port Of Defect DCSG00053744)
 -Upto 90% performance drop with expander attached configuration.(CSG00153860 (Port Of Defect DCSG00215210)
 -ExtManPage41 TX Values are not being applied / run by AERO SERDES(CSG00311524 (Port Of Defect DCSG00313276)
 -[NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive(CSG00136092 (Port Of Defect DCSG00243680)
 -PL: PCIe switch discovery can cause processor exception when setting enclosure information(CSG00063530 (Port Of Defect DCSG00063552)
 -PL backend PCIe: PL fault 0xD308 is observed with Aero and Atlas connected in bad clock environment(CSG00134207 (Port Of Defect DCSG00137697)
 -Aero: backend PCIe: link failure following link down(CSG00043821 (Port Of Defect DCSG00048732)
 -MCTP: SenseData not available for a failed command sent over OOB.(CSG00054655 (Port Of Defect DCSG00057485)
 -Number of initiators gets decremented to 0xFF(CSG00051990 (Port Of Defect DCSG00053834)
 -Quotes present in NVDATA XMLs(CSG00045528 (Port Of Defect DCSG00045606)
 -Incorrect Man page 7 Phy-Slot mapping set for 9500-xx channel HBAs(CSG00061349 (Port Of Defect DCSG00062359)
 -[Aero] Change the Manpage 7 Phy to Connector settings and Disable NVMe support in ManPage9(CSG00031186 (Port Of Defect DCSG00044352)
 -[SPDM IT] Return actual size of certificate chain content to SPDM LIB(CSG00233805 (Port Of Defect DCSG00245634)
 -PL SATA only : SATA init timeout observed due to drive taking longer to respond to sanitize status ext(CSG00225935 (Port Of Defect DCSG00227376)
 -IOC Exceptions not getting cleared after flashing the BIOS image with correct ROP version(CSG00226395 (Port Of Defect DCSG00227987)
 -AXI access errors causing FW asserts or faults due to invalid SATA passthrough commands(CSG00215338 (Port Of Defect DCSG00243095)
 -(SATA Only) SCSI ATA Passthrough command with data transfer fails.(CSG00120976 (Port Of Defect DCSG00121420)
 -Locate PD fail on SGPIO enclosure when GroupId is disabled in Nvdata.(CSG00034489 (Port Of Defect DCSG00041403)
 -Fault 0x6109 while running IOs and device remove test.(CSG00082201 (Port Of Defect DCSG00083887)
 -PL : Missing drives during AC power cycle test(CSG00275868 (Port Of Defect DCSG00301822)
 -NVMe Init Error List has drive entry missing when multiple Bad PDs are inserted(CSG00113697 (Port Of Defect DCSG00121316)
 -[Aero/Ventura]Allow the backplane detection state machine to retry the FRU detection.(CSG00219908 (Port Of Defect DCSG00222984)
 -(SATA Only) MODE SELECT (6|10) to SATA drive with DEXCPT set fails if DEXCPT is already set.(CSG00131574 (Port Of Defect DCSG00134494)
 -Toolbox clean command sent to clean flash fails.(CSG00059302 (Port Of Defect DCSG00062455)
 -[VSes] SCSI State not correctly set for some error response to SCSI commands.(CSG00312554 (Port Of Defect DCSG00324764)
 -PL: TM Device Reset to NVMe drive under out of LMID condition can cause Data Abort Exception to the processor(CSG00036763 (Port Of Defect DCSG00048676)
 -Index out of range is observed for print in ring buffer logs(CSG00134669 (Port Of Defect DCSG00139071)
 -Aero_scrutinycli: "Device -c" command output is not matching with the firmware cli parameter values in Aero behind atlas configuration.(CSG00121852 (Port Of Defect DCSG00127910)
 -PL Fault 0000e40e while booting OS with bad NVMe drive(CSG00109053 (Port Of Defect DCSG00118379)
 -NVMe devices VPD page 83 NAA descriptor may conflict with EUI64 ID reported(CSG00060347 (Port Of Defect DCSG00136105)
 -Moving Controller From Single VSES config to a multi-VSES config causes issues in windows OS.(CSG00071784 (Port Of Defect DCSG00080399)
 -[VSes] Element status set to 'Unknown' in SES page 2 of VSES for some phys where nothing is connected.(CSG00333163 (Port Of Defect DCSG00343847)
 -PL NVMe : PCI task management is not getting completed.(CSG00231422 (Port Of Defect DCSG00266052)
 -Fix ring buffer decoder's slowness with decoding a trace buffer(CSG00050675 (Port Of Defect DCSG00051120)
 -NVMe repair command fails with 'No drive support for recovery' loginfo(CSG00129498 (Port Of Defect DCSG00137668)
 -NVMe drives not discovered and Event replay in enclosure slot mapping not working as expected.(CSG00078212 (Port Of Defect DCSG00080846)
 -As part of the Device Add\Removal Event, the enclosure handle passed on by the PL FW to the upper layer is incorrect.(CSG00298128 (Port Of Defect DCSG00299896)
 -[Aero] Fault 0xA03 observed when updating FW with a bad NVMe drive in the topology(CSG00132639 (Port Of Defect DCSG00136250)
 -pl: NVMe: chain to PRP SGL for non-read/write IO may be handled improperly(CSG00408313 (Port Of Defect DCSG00427399)
 -scattered file changes to include some debug prints and also minor change to debug print(CSG00057124 (Port Of Defect DCSG00057818)
 -Firmware asserts during customer specific UBM Backplane enumeration.(CSG00058770 (Port Of Defect DCSG00061183)
 -[Aero][AutoPort Enable] Erase persistent config pages is not retaining the VPD and sas address(CSG00074378 (Port Of Defect DCSG00114250)
 -Import certificate command is failing via In-band(CSG00212544 (Port Of Defect DCSG00215132)
 -[Aero][PLDM] Update to Latest PLDM library v13(CSG00137629 (Port Of Defect DCSG00138016)
 -AXI access error from TxDMA engine when certain errors occur during Task Management processing(CSG00078508 (Port Of Defect DCSG00235435)
 -SPDM IT:SPDM BMC bring up on P2 server(CSG00238540 (Port Of Defect DCSG00241397)
 -SATA Only: Command timeout observerd on SATA drives(CSG00344039 (Port Of Defect DCSG00356005)
 -Aero: PL with newer Atlas FW (4.2) has extra slot number in the Atlas enclosure(CSG00284238 (Port Of Defect DCSG00291431)
 -Aero A0: In Windows OS redundant disks detected when controller connected to Elrond Ex1(CSG00061406 (Port Of Defect DCSG00065448)
 
EnhancementRequests:
 -PL: Support Managed Switch (Atlas) slot range VSEC command for its single MPT mode(DCSG00071626)
 -BST: Add Ventura activity server and enclosure to test config(DCSG00079826)
 -SEA IT TRNG HW enable(DCSG00098752)
 -Bring up OEM Specific BST Server(DCSG00325843)
 -Enable UBM BST support for Aero(DCSG00063407)
 -Health Data Events - Create counters for various Health Data Events(DCSG00078912)
 -Re-naming few functions in module-object-verb format(DCSG00027061)
 -Ventura/Aero: Add Ext. Man Page 48 to store CoreDump options(DCSG00026309)
 -Add Aero/Sea Info to Ventura Summary Release Notes(DCSG00077941)
 -BST: Add support for Drive Control Modules to cable breaker test cases.(DCSG00256443)
 -Aero3: SecureBoot BIOS Image Download with new Key is failing(DCSG00233694)
 -Platform related configuration changes updation(DCSG00039844)
 -Port secureSignBin.exe for MARGAY signing to GCP server environment(DCSG00040377)
 -Update HWBIC Generation XMLs for CQ9(DCSG00100142)
 -SPDMLIB: OEM requested to not report Get Measurement Capable(DCSG00323053)
 -Release Automation: Submit auto-BST jobs(DCSG00091315)
 -Resolving the compilation conflicts while integrating the library with FW(DCSG00045448)
 -Certificate read and Write wrapper functions & Slot management(DCSG00105005)
 -Automate Build Job and Release Job Submission Process(DCSG00045139)
 -Remove A0 raw fw rawA0.fw file from release scripts(DCSG00211914)
 -BST: Aero Activity server with Atlas switch(DCSG00225036)
 -Define Macros/inline functions(DCSG00027051)
 -BST: A test to verify slot counts(DCSG00238332)
 -MPI changes to configure backend ASPM(DCSG00051277)
 -Avenger support for the LIBSPDM(DCSG00081168)
 -UBM BST: Ensure UBM BP details reported by FW are accurate.(DCSG00227823)
 -Add IT+Expander controller to OEM BST server(DCSG00286591)
 -pl: SATA: vendor specific ATA Standby handling(DCSG00074400)
 -Aero/Ventura: Enable easier debug when SPI FLASH is bad(DCSG00058537)
 -Log SPDM events entries in log page 0(DCSG00139949)
 -PL: NVMe Drive Repair(DCSG00055563)
 -Implement a secure version of memset for SPDM code to use to zero out buffer(DCSG00208365)
 -Automate version update stage in release process(DCSG00122144)
 -SPDM LIB: Implement version scheme(DCSG00072483)
 -Aero multi-party signing partial signing of images(DCSG00048670)
 -PL logic to create VSES instances per Backplane number(DCSG00069245)
 -SPDM_LIBRARY: Change for SPDM Policy Implementation(DCSG00097417)
 -[Aero][Ventura] Sign windows build applications and avoid antivirus from deleting them.(DCSG00025757)
 -FD should move to DOWNLOAD state immediately upon successfully sending the response of UDATE_COMPONENT.(DCSG00046402)
 -Allow General Processing Failure from Atlas on unsupported commands to not result in 0xEA20 fault(DCSG00170698)
 -Added SPDM lib to IT FW code base and handle MCTP VDM SPDM commands(DCSG00063688)
 -MBEDTLS LIB: Enhancement to source of randomness for generating key pair(DCSG00148786)
 -Define APIs for PLDM debug infrastructure and Implements debug routine for PLDM Base(DCSG00026992)
 -[Aero] [SPDM] Support Export Certificate Signing Request command(DCSG00063692)
 -Ventura/Aero: Update SPI flash test to print better failure information(DCSG00070917)
 -Remove cdi get for Avenger(DCSG00152679)
 -Port changes from old db to new DB(DCSG00014692)
 -BST: set SRIS after every fw download(DCSG00150322)
 -Signing Linux executables via GPG method in HSM(DCSG00077215)
 -PL: Coordinate reset on Atlas FW update to limit IO disruption to NVMe drives behind Atlas(DCSG00097342)
 -MbedTLS: Explicitly make enumerator value of enum type to 4-byte value(DCSG00054557)
 -MBEDTLS LIB: Rename sha256.h header file to avoid conflict with MR FW sha256.h header file(DCSG00068675)
 -Enable 24 PCIe device support for Aero External boards.(DCSG00278073)
 -SPILIB 2.0: Add capability to support Winbond Parts with Factory Quad bit Disabled(DCSG00140236)
 -Release Automation: Validate FW Header post Package Creation(DCSG00055071)
 -CM Utility to perform automated Deliver and Rebase actions(DCSG00083856)
 -Release Automation: create Aero IT FW only Release Order Package(DCSG00066845)
 -SPILIB 2.0: Add support for Block Protect bits configuration(DCSG00170752)
 -SPILIB2: Add support for Macronix MX25U25691G part(DCSG00068680)
 -SPDM LIB: Implement SPDM Get Measurement command(DCSG00234758)
 -CFGI: support build persistent config region from MPB2(DCSG00077614)
 -Disable hardware debug ports(DCSG00143569)
 -pl: backend PCIe: PCIe Hinting(DCSG00050640)
 -BST: Config update with Blr servers data for slot count(DCSG00248916)
 -Check if all BP slots and drives are discovered after FW upgrade(DCSG00087155)
 -Aero/Ventura: Add CLI to test QE bit modification(DCSG00148653)
 -pl: NVMe: handle Namespace Not Ready error during NVMe init(DCSG00071652)
 -MbedTLS Lib: disable file system related functions & enable memory allocation and prints functions to be compiled in CPP environment(DCSG00060384)
 -Modify the UBM BST code with respect to new BST scrutiny APIs.(DCSG00063258)
 -CDI & Key Generation source integration with IT FW(DCSG00063690)
 -Added Carriage Return (\r) in PLDM common library debug strings(DCSG00069752)
 -Update PLI Spec(DCSG00008045)
 -pl: backend PCIe: examine BAR attributes following endpoint/switch reset(DCSG00060688)
 -UCM Action tool feature to support rebase using latest baseline(DCSG00125616)
 -Update Sea Channel XMLs to PCI Device ID 0xE6(DCSG00079238)
 -SECUREBOOT_LIB: Move hardware touch (ApSha HASH & HMAC and OTP eFuse Read) from MR SPDM code to Secure Boot Lib(DCSG00082166)
 -Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that are from SCGCQ and DCSG.(DCSG00105430)
 -NVMe Drive Init failure Error Reporting(DCSG00055566)
 -MBEDTLS LIB: Change large local variable memory allocation from the stack to dynamic memory allocation from the heap(DCSG00087564)
 -Aero/Ventura: Move DMCore hardware file to common(DCSG00007511)
 -Add Avenger support for libmbed tls.(DCSG00051695)
 -pl: NVMe: handle Namespace Not Ready error during NVMe init (part 2)(DCSG00075871)
 -BST: Update scripts to run Customer fw on channel adapter(DCSG00082887)
 -Enable 24 NVMe drive support by default for external controllers.(DCSG00305223)
 -Implement event message supported, event message buffer size and platform event message for PLDM type 2 - monitoring and control app.(DCSG00149551)
 -Resolving the compilation conflicts while integrating the library with FW(DCSG00045470)
 -PLDM - Add Linked List Traverse utility and correct TID API function(DCSG00165389)
 -UpdateVersion tool to change and update version information in ClearCase(DCSG00072590)
 -Implemented change to use FTP instead of UNC for upload / download of unsigned / signed artifacts to workaround firewall issue.(DCSG00129388)
 -[Aero][SPDM] IOP framework to support CFGI Reads and Writes(DCSG00076512)
 -[SPDM]SBlib upgrade to 2.02(DCSG00091314)
 -Provide Configurability For SPDM Library(DCSG00045604)
 -Added documentation for some scenarios(DCSG00027067)
 -MBEDTLS LIB: Implementation: Use CDI to generate ECDSA key pair(DCSG00067411)
 -[BST] Add the corrective action in BST scripts to check if SAS address is retained after persistent erase(DCSG00216341)
 -BST: Verify version control file from fw(DCSG00268618)
 -SPDM_LIB: Support to build Challenge buffer with multiple GET_CERTIFICATE/CERTIFICATE_RESPONSE(DCSG00225175)
 -Update Version descriptors for standard inquiry data of SATA and vSES devices(DCSG00037325)
 -[Aero SPDM] XSD changes to support SPDM version in a new manufacturing page(DCSG00103227)
 -Update NVMe to SCSI Error code translation.(DCSG00098339)
 -Added "pl serdes tx" and "pl serdes rx" command(DCSG00053828)
 -Support for NVMe Firmware Download when the image size exceeds the SNTL Transfer limitation.(DCSG00053656)
 -MBEDTLS LIB: Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust(DCSG00216867)
 -Shrink MbedTLS library size(DCSG00059001)
 -Log 0 SPDM events for certificate slot & key management(DCSG00322202)
 -Support MPB2 write/read into manufacturing region(DCSG00063677)
 -PLDM Type 2 - Implement support for dynamic PDR repository change(DCSG00165393)
 -PLDM: Implement PLDM Type-6 library API and commands(DCSG00064565)
 -Fix Mbedtls build scripts to accommodate Aero and Avenger(DCSG00150272)
 -PLDM library support to report multiple PLDM App versions to BMC(DCSG00026969)
 -Correcting the print function configuration(DCSG00047741)
 -XSD and NVDATA changes to support SPDM manufacturing and Security pages(DCSG00063680)
 -BST: Customer specific Release/Activity BST at BLR(DCSG00064578)
 -SECUREBOOT_LIB: Move SRK and CCR eFuse register access functions to SBLIB(DCSG00086765)
 -Package Stamping Verification(DCSG00096506)
 -PLDM Type 6: Add debug strings for Type-6 library(DCSG00065842)
 -Implement customSign.exe CLI wrapper utility to help customers sign with their private key(DCSG00234646)
 -Release Automation: Integrate utility for deliver/rebase into release scripts.(DCSG00094677)
 -Config file changes to including prints(DCSG00047716)
 -BST: Customer Aero based ROP BST and setup at BLR(DCSG00109334)
 -pl: backend PCIe: add debug print for a discovery failure case(DCSG00083082)
 -Implement support for Cross certificate and command - Windows signing using CNG Provider with HSM Protected Key(DCSG00030211)
 -Release Automation: updates for rebase operation(DCSG00134475)
 -MbedTLS lib integration with IT FW(DCSG00063687)
 -Release Automation: Integration of all script modules(DCSG00120937)
 -MBEDTLS: Implementation: Implement Subject Name validation for CSR (Certfificate Signing Request) and CSR generation(DCSG00069942)
 -Implemented secureSignCNG.exe CLI signing tool for Windows Signing.(DCSG00023491)
 -Providing Link and Device Related Counters(DCSG00056834)
 -PLDM: Implement generic string and linked list utility functions(DCSG00056271)
 -Aero3: Harden Managed Switch SES (Atlas) SES Page 0Ah translation with error injection framework(DCSG00037053
 -Release Automation: Automate state transitions for ReleaseOrder(DCSG00035457)
 -ComboSerdes: add functionality for bypass ready waiting(DCSG00167482)
 -Aero SPDM Sblib change: provide sblib interface to disable specified HW debug port.(DCSG00166877)
 -Serial mode support for S25FL512S SPI flash part(DCSG00054211)
 -MBEDTLS LIB: Implement version scheme(DCSG00072481)
 -Aero: Change XMEMCOPY default to disabled in Aero(DCSG00082841)
 -PLDM: Implement Redfish PDRs and APIs(DCSG00060505)
 -SPDM library: Adding PLDM print module style.(DCSG00060323)
 -PL UBM support UBM for PCIe SW upstream port config(DCSG00120726)
 -Add SasSerdesCtl0_7 registers to pl serdes(DCSG00069982)
 -Implement Debug routines for PLDM Type-5 Module(DCSG00027039)
 -pl: NVMe: update Block Limits VPD page translation(DCSG00055387)
 -CFGI support for write/read into manufacturing region MPB2.(DCSG00065597)
 -Add support for C++/CPP compile for libspdm(DCSG00051200)
 -[Aero IT SPDM] Attestation policy at the boot-up time.(DCSG00063691)
 -Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images(DCSG00143847)
 -[IT SPDM] Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust(DCSG00218564 (Port Of EnhancementRequest DCSG00322020)
 -Aero Secure Boot: Add Key Update Pending Check for 'COMPLETE' Image Download(DCSG00241566 (Port Of EnhancementRequest DCSG00250024)
 -Advertise certain Secure Boot Properties using a config page for Application to be able to display it(DCSG00078835 (Port Of EnhancementRequest DCSG00093843)
 -Enhancement to source of randomness for generating key pair(DCSG00208477 (Port Of EnhancementRequest DCSG00250093)
 -[IT SPDM] Implement client APIs for SPDM Get Measurement command.(DCSG00256411 (Port Of EnhancementRequest DCSG00293435)
 -Aero SAS Performance Enhancement on AMD Rome as part of PR(DCSG00064583 (Port Of EnhancementRequest DCSG00065934)
 -SPDM IT: Add memory allocation/free for SPDM_LIB(DCSG00229260 (Port Of EnhancementRequest DCSG00241396)
 -Modify Ventura Build scripts to add a new Signed image with different AVSO Setting in FW RO(DCSG00231216 (Port Of EnhancementRequest DCSG00231535)
 -[SPDM IT] Export CSR & Import Cert Open & Close Session(DCSG00221406 (Port Of EnhancementRequest DCSG00257575)
 -Update the event logging when the "CoreDump" region is erased from ScrutinyCLI command(DCSG00367325 (Port Of EnhancementRequest DCSG00418780)


Version 14.125.05.00-4
---------------
    BIOS            Firmware      UEFI Driver   
 9.27.00.00      14.00.04.00     14.00.01.00
 
Fixes：
code no fix
 
Version 14.125.05.00-2
---------------
    BIOS            Firmware      UEFI Driver   
 9.27.00.00      14.00.04.00     14.00.01.00